• Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.

AMNPS with Mr. Gasser

cmayna

Master of the Pit
OTBS Member
★ Lifetime Premier ★
3,072
810
Joined Jun 23, 2012
Doing some wings in my Masterbuilt gasser but using the AMNPS cage at the bottom underneath the burner. Oh and did I tell you that it finally decided to start raining? Hey! where's my golf umbrella? Smoking with Hickory pellets.



Side view of lower box which has breather holes around it:


Front view:





Tapayakin' from my iphone
 
Last edited:

miersc77

Smoke Blower
100
12
Joined Jan 10, 2015
Hey cmayna cmayna I was doing some research and have some questions for you if you don't mind. First, how do you like the needle valve mod? I already ordered one but can I really get temps around 220*? How about blow out?
And your smoke stack, is there much affect? I was smoking some eggs and noticed the ones closer to the back were not as smoked as the ones up front. Does the stack help with the odd draft?

I'm going to steal your umbrella idea too, just cause its cool!

Thanks for your help!
 

cmayna

Master of the Pit
OTBS Member
★ Lifetime Premier ★
3,072
810
Joined Jun 23, 2012
I must admit that I haven't smoked anything less than 225 for quite some time, thus I haven't been using the needle valve.  It is currently wide open and I just turn down the gasser's control knob.  I really like the smoke stack I installed.  Sometimes wish it was taller, so all I do is to slide a round shaped piece of cardboard over the current smoke stack and suddenly it's 2 feet tall.  My smokes are pretty uniform but I can't tell too much about the smoke color until I do some cheese.  Even then most of the blocks are pretty uniform.

Craig
 

miersc77

Smoke Blower
100
12
Joined Jan 10, 2015
I must admit that I haven't smoked anything less than 225 for quite some time, thus I haven't been using the needle valve.  It is currently wide open and I just turn down the gasser's control knob.  I really like the smoke stack I installed.  Sometimes wish it was taller, so all I do is to slide a round shaped piece of cardboard over the current smoke stack and suddenly it's 2 feet tall.  My smokes are pretty uniform but I can't tell too much about the smoke color until I do some cheese.  Even then most of the blocks are pretty uniform.

Craig
Thanks for the quick reply! I would be just fine with 225* or really anything below 250* With my current set up my temps just keep climbing. Hit around 310* last night while I was smoking some chicken breast. Tried messing with the tank valve but that was such a pain and constantly needed adjustment. My valve should be here tomorrow and you having giving me hope. I think I will do the stack as well to try and even the smoke. Did you just block off the original upper vent? Again thank you!
 

cmayna

Master of the Pit
OTBS Member
★ Lifetime Premier ★
3,072
810
Joined Jun 23, 2012
I have it opened just a tad.   Hmmmm, sure sounds like a needle valve might help you big time.   If you end up choking the flame down a lot, consider building a wind protector around the bottom of your smoker to help prevent a gust from blowing out your flame.

This coming weekend while smoking some Salmon nuggets in one of my big Chief smokers, I'm going to do some more bacon wrapped chicken chunks in my gasser.   Dual smoking....gotta love it.
 

miersc77

Smoke Blower
100
12
Joined Jan 10, 2015
That's what I'm hoping for! Thanks for the idea about a wind block, I'll have to keep that in mind. I haven't tried any fish yet but gotta say I will do those bacon wrapped chicken nuggets sooner than later! Hope you do a Q, happy smoking!
 

Latest posts

Hot Threads

Top Bottom
  AdBlock Detected

We noticed that you're using an ad-blocker, which could block some critical website features. For the best possible site experience please take a moment to disable your AdBlocker.