• Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.

Opinions needed on a grinder

pandemonium

Master of the Pit
1,983
14
Joined Aug 4, 2009
sounds like something else, maybe the blade is in backwards? thats what it sounds kinda like to me the flat part needs to be up against the plate. might sound dumb but i think i had mine in wrong the first time and its easy to do.
 
Last edited:

pandemonium

Master of the Pit
1,983
14
Joined Aug 4, 2009
Try another one first im telling you mine has been good and also you want to almost have the meat frozen because it grinds much nicer and how big of pieces did you cut it up the pork in? its not a heavy duty grinder that can do as big of pieces as an expensive one so you have to cut the meat pretty small and dont force it in let the grinder do the work you can hear when it is straining and dont over due it.
 
Last edited:

cabin fever

Smoke Blower
116
11
Joined Dec 1, 2009
I tried the blade the other way around the second time when I used the coarse plate and it didn't seem to make a difference. I cut the pork butt into small strips to make sure it wouldn't bog the grinder down either. I kind of planned on this happening with a cheaper unit so I'm not upset. I can hang onto the Kitchen Aid as long as I need to so there's no worries. 
 

pandemonium

Master of the Pit
1,983
14
Joined Aug 4, 2009
ok well maybe you got a bad one, but give another one a try they will return it.

heres a video of mine

 

big-guy

Fire Starter
50
11
Joined Sep 12, 2010
My guess the blade is in backwards.  It should be put on the auger with the flat surface facing outward, next add the plate then the big retaining screw/ring. Does your motor have a reverse switch? maybe you are running in reverse?
 

pandemonium

Master of the Pit
1,983
14
Joined Aug 4, 2009
My guess the blade is in backwards.  It should be put on the auger with the flat surface facing outward, next add the plate then the big retaining screw/ring. Does your motor have a reverse switch? maybe you are running in reverse?

thats what i think too, theres no reverse on this grinder
 

big-guy

Fire Starter
50
11
Joined Sep 12, 2010
250 watts is pretty anemic, the maximun power that can be safely used on a typical household 120v 15 amp receptical would be 1800 watts
 

pandemonium

Master of the Pit
1,983
14
Joined Aug 4, 2009
250 watts is pretty anemic, the maximun power that can be safely used on a typical household 120v 15 amp receptacle would be 1800 watts
Well kitchen receptacles are 20 amp and 250 watts is only  2 amps so I dont get your point? Yes its not a beast of a grinder that's why its about 40 bucks, but it does the job.
 

big-guy

Fire Starter
50
11
Joined Sep 12, 2010
My point was that its a very low powered grinder, It might bog down even if assembled properly , but fed too fast.
 

lindamalbert

Newbie
1
10
Joined Dec 10, 2010
My husband and I just bought this grinder and it went through our whitetail hamburger gind 90# of venison and 10# of suet with no trouble at all and was very fast. In addition we ground 80# or so of mule deer meat with 10# of pork shoulder for sausage. Half of that became breakfast sausage and half we seasoned and stuffed in to hog casings for kielbasa. There was no heat buildup at all that we could feed from the housing. We bought this grinder to save the motor of the kitchenaid stand mixer for which we have the grinding and stuffing attachments. The Kitchenaid was a lot slower. The Super 3000 and the Kichenaid tubes both hold about the same length of casings and the setup for the stuffing attachments were not obviously clear, but we got it and the 3000 made very quick work of it. We would have been twice as long with the Kitchenaid.

Linda Albert
 

frassettor

Fire Starter
30
10
Joined Nov 17, 2007
A few years ago I bought a Torrey 3/4 horse. Even though it costed me  a few grand, its the best investment I made. Cabin fever hit it right on..IMO
 

Latest posts

Hot Threads

Top Bottom
  AdBlock Detected

We noticed that you're using an ad-blocker, which could block some critical website features. For the best possible site experience please take a moment to disable your AdBlocker.