brinkmann pitmaster mods

[waygu tim]

hi all today i started work on my brinkmann pitmaster we did all of the design work and ordered the metal for it using expected metal for the charcoal basket and 1/4 inch metal for the baffle and turning plates

IMG_0113.JPG

• waygu tim
• Apr 3, 2014

IMG_0111.JPG

• waygu tim
• Apr 3, 2014

IMG_0108.JPG

• waygu tim
• Apr 3, 2014

IMG_0109.JPG

• waygu tim
• Apr 3, 2014

IMG_0110.JPG

• waygu tim
• Apr 3, 2014

 

[kc5tpy]

Hello Tim.  Lookin good so far.  Good luck.  Keep Smokin!

Danny

 

[waygu tim]

hi guys well i got my metal parts today we are about done on the smoker build the baffle plate is made out of 3/16 metal and the tuning plates are made of 1/4 metal need to finish the front shelf and brace the legs and extend the chimney down to grate level and replace the wheels and repaint it then put the seal on then i am done i am so happy right now  i did fire it up today i could the the difference right away it was amazing

IMG_0120.JPG

• waygu tim
• Apr 16, 2014

IMG_0121.JPG

• waygu tim
• Apr 16, 2014

IMG_0122.JPG

• waygu tim
• Apr 16, 2014

IMG_0123.JPG

• waygu tim
• Apr 16, 2014

IMG_0124.JPG

• waygu tim
• Apr 16, 2014

IMG_0125.JPG

• waygu tim
• Apr 16, 2014

IMG_0126.JPG

• waygu tim
• Apr 16, 2014

IMG_0127.JPG

• waygu tim
• Apr 16, 2014

IMG_0128.JPG

• waygu tim
• Apr 16, 2014

IMG_0129.JPG

• waygu tim
• Apr 16, 2014

IMG_0114.JPG

• waygu tim
• Apr 16, 2014

IMG_0115.JPG

• waygu tim
• Apr 16, 2014

IMG_0116.JPG

• waygu tim
• Apr 16, 2014

IMG_0118.JPG

• waygu tim
• Apr 16, 2014

IMG_0119.JPG

• waygu tim
• Apr 16, 2014

 

[waygu tim]

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0144.JPG

• waygu tim
• May 2, 2014

IMG_0146.JPG

• waygu tim
• May 2, 2014

IMG_0147.JPG

• waygu tim
• May 2, 2014

IMG_0149.JPG

• waygu tim
• May 2, 2014

IMG_0150.JPG

• waygu tim
• May 2, 2014

IMG_0151.JPG

• waygu tim
• May 2, 2014

IMG_0152.JPG

• waygu tim
• May 2, 2014

 

[aaardvark]

Tim:

Looks great.  I am about to start a restoration of a BPD and want to make the same mods.  Do you happen to recall the measurements for the heat shield.  Top I can figure out, but 1) bottom and 2) some way to guesstimate the curve would be very helpful.

 

[waygu tim]

hi there i will try and help u the best way i can a email address or phone number that would be grate and make sure to use only dry wood is what i found works the best

 

[aaardvark]

Tim:

Thanks for the speedy reply.

You can reach me at [email protected]

Rob