• Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.

Brisket Failure to Success!

jsk53

Smoke Blower
140
42
Joined Apr 7, 2013
Here is my second attempt at a beef brisket. My first one, which I did a post on last week, was a complete failure.  After getting a number of replies from my brothers here on the forum, I got great suggestions on how to correct the problems. I also picked up a new rub recipe as I really didn’t like the first one I used. I also changed from pecan to hickory.  As my new MES40 had just arrived as a replacement for my well used MES30 and armed with new procedures, I picked up another packer brisket (13 lbs) and went at it. This time I did little trimming as the fat cap was already at about ¼” but I did manage to trim off about a pound and a half of fat, and desilvered the top a bit


As the smoker was getting up to temp, ( I had already seasoned the new smoker the day before), I mixed up the rub, oiled the brisket with olive oil, and worked in the rub on both sides. It took about an hour for the smoker to stabilize at about 230 degrees.


Into the MES40 and we’re off..


I kept up the smoke for 6 hours and kept the smoker at the 225-230 degree mark.


After 6 hours, I pulled the brisket, put in the meat probe and wrapped it in heavy duty foil two layers thick. And back on the smoker.


About 4 ½ hours later, the meat probe in the flat hit 200 degrees.  I pulled it and put the wrapped brisket in a cooler, covered with towels for an additional 2 hours to rest.  I was amazed at how hot it still was when I got it out and uwrapped it.


After letting it sit unwrapped for a few minutes, I sliced a couple pieces off and it was tender and moist. The flavor from the rub was perfect and the hickory did the trick.


This was a marked improvement over my first failed attempt and I think the adjustments I made based on the help and input I got from several folks here, turned a failure into a winner!  Thanks to all.
 

pigfeet33

Fire Starter
58
17
Joined Mar 30, 2016
That brisket looks awesome! Did you get a good smoke ring in the MES? I have been looking at getting one for a while but my buddy who has one says it's hard to get a good smoke ring (not that smoke ring is super important when you have a brisket come out looking like yours). Great job! [emoji]128077[/emoji]
 

hardcookin

Master of the Pit
OTBS Member
2,242
685
Joined Aug 13, 2015
Congratulations on your 2nd attempt Looks pretty darn good. Thumbs Up
 

SmokinAl

SMF Hall of Fame Pitmaster
Staff member
Moderator
OTBS Member
★ Lifetime Premier ★
44,515
6,224
Joined Jun 22, 2009
The brisket looks fantastic!

Points for a great second try!

Al
 

jsk53

Smoke Blower
140
42
Joined Apr 7, 2013
That brisket looks awesome! Did you get a good smoke ring in the MES? I have been looking at getting one for a while but my buddy who has one says it's hard to get a good smoke ring (not that smoke ring is super important when you have a brisket come out looking like yours). Great job! [emoji]128077[/emoji]
I didn't get a smoke ring but the flavor was sure there. I've read that using an electric or gas smoker won't create a smoke ring. Not sure why, but that's been my experience as well. I like the temp control of an electric smoker so I guess that's the trade-off. Thanks for the comment!
 

crazymoon

Smoking Guru
OTBS Member
SMF Premier Member
6,032
1,550
Joined Aug 24, 2014
Jsk53, Nice job on the brisket  sir !
 

smokeymose

Master of the Pit
SMF Premier Member
3,214
853
Joined Aug 13, 2015
Smoke ring is like "bark" IMHO, pretty but not really needed.If it's tender and tastes good, you've got a winner!

:points:

Dan
 

Hot Threads

Top Bottom
  AdBlock Detected

We noticed that you're using an ad-blocker, which could block some critical website features. For the best possible site experience please take a moment to disable your AdBlocker.