HELP! MES not putting out smoke.

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

smoking in ft. collins

Smoke Blower
Original poster
Sep 7, 2006
143
17
Fort Collins, CO
Hello,

I have a new Masterbuilt Electric and am using it for the second time. I reported that it did not generate much/any smoke the first time I used it and was told NOT to soak the hickory chips.

Today I have it fired up and it is sitting at 220* with DRY chips and there is no smoke coming out.

The chips are in the pan provide by the MFG and the pan sits in a grate but does NOT touch the heating element.  In fact the pan is about half an inch above the element.

Any ideas???

I am ready to fire up my charcoal smoker.
 
Chargriller barrel with a side smoke box.  it is firing up now.

I really want to understand why the thing doesn't work.  I have also been told that the amazing smoke generator does not work well at altitude (I am at 5000 feet).
 
So your at 220 and the chips won't smoke... That is very strange. Call masterbuilt before they close for the day. Even if you use the other smoker for dinner at least you can have them help problem solve and possibly send you new parts today
 
Is your chip tray hot? Is it inserted properly caressing the heating element?

Are you being a nosy cook? You must leave the door shut and let the heater come on. its takes longer than 10 mins. its electric.

Try putting the temp to 275 and see if it smokes. open the outlet vent completely so it can draw a draft.
 
I have the MES 40, and I've never had a problem getting smoke at lower temps. Makes me wonder also if you might be having an element problem. I was actually getting too much smoke for my tastes, so I went the AMNPS route. Just got it this week and will be using it for the first time this weekend. But back to your issue, I agree, a call to Masterbuilt wouldn't be a bad idea.
 
 
Is your chip tray hot? Is it inserted properly caressing the heating element?

Are you being a nosy cook? You must leave the door shut and let the heater come on. its takes longer than 10 mins. its electric.

Try putting the temp to 275 and see if it smokes. open the outlet vent completely so it can draw a draft.
caressing he heating element?  It is a half inch away from the element.  I figure that is my problem.

Oh and there is NO vent.  Only a hole in the back for the smoke to escape.
 
Last edited:
I've got the same unit. I used the chip tray once. After reading a bunch of stuff on this forum, I bought an A-maze-n Tube Smoker. The results have been great. Don't think I'd ever use chips again. I've smoked ribs, brisket, cheese, trout, salmon, and pork loin. All with the MES and a tube smoker. They have all been great. 
 
 
I've got the same unit. I used the chip tray once. After reading a bunch of stuff on this forum, I bought an A-maze-n Tube Smoker. The results have been great. Don't think I'd ever use chips again. I've smoked ribs, brisket, cheese, trout, salmon, and pork loin. All with the MES and a tube smoker. They have all been great. 
Did the chip tray touch the heating element?
 
Just took the cover off mine to double check. Don't want to give you bum info. No, the tray doesn't touch or rest on the element. I would say it sits about 1/8 to 1/4  inch above the element. It seemed closer to the element in the front and bit further from the element in the rear. I tried to put a yellow pencil between the bottom of the tray and the element to create a visual for a picture. The pencil wouldn't fit. I'd guess it was too large by at least 2x. 
 
Last edited:
 
Hello,

I have a new Masterbuilt Electric and am using it for the second time. I reported that it did not generate much/any smoke the first time I used it and was told NOT to soak the hickory chips.

Today I have it fired up and it is sitting at 220* with DRY chips and there is no smoke coming out.

The chips are in the pan provide by the MFG and the pan sits in a grate but does NOT touch the heating element.  In fact the pan is about half an inch above the element.

Any ideas???

I am ready to fire up my charcoal smoker.
1/2" is probably too far from element.

The first one I got had an extra piece of metal between the element & the chip drawer.

It wouldn't smoke until about 220*, and then only when the element was on.

At that time they had a Retro-fix, and they sent one to me.

This one didn't have the extra piece of metal, and the element was too close to the chip drawer, causing the chips to flame up.

I probably could have bent things around to get it to work better, but it would never work like an Amazing Smoker.

SOoooo  I filled my AMNPS with pellets, lit it, and put it in, giving me perfect smoke for up to 12 hours without touching it.

I never looked back, and we smoked Happily Ever After.

Bear
 
Ok, I have been doing some reading and I can't see similarities between my smoker and others so here are some pics.
era4uqeb.jpg


Inside chip tray.

y5ezage3.jpg


Intake hole.

u6eqa8as.jpg


Exhaust hole.

vudabane.jpg


There are no other vents.

Did I but the wrong model?
 
Looks just like mine. Is the bottom tray, which holds the chip tray, in the slots on the side straight? In your picture, it looks a bit racked. 
 
Ft Collins,

Yes, like Foamy said, you have the analog smoker----I should have asked, but there are so few of them I forget to.

I would think since you are at 5,000 ft, I would go with the Amazing tube smoker, because they are easier to keep smoking.

Just click on the business card below "A-MAZE-N-SMOKER", and check out the AMNTS.

Bear
 
Last edited:
I gave up on the electric last night.  I talked to Masterbuilt today and they said that the heating element should *touch* the chip tray and that I should bend the element up to touch it.

What size tube do most people use?

Thanks for all the input.

John
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky