Got my pipe
- Thread starter bishgeo
- Start date
-
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.
ribwizzard
Master of the Pit
dockman
Smoking Fanatic
maple sticks
Smoking Fanatic
My experience its the cuts that are expensive. Did they break the cost down? Steel per LB and charge for cut?
- Ribwizzard
- offline
- 1,879 Posts. Joined 5/2012
- Location: Orlando and Tampa Florida
- Points: 48
Nice, what did you give for it?
My opinions and suggestions are just like my farts, they never stop.
ReplyQuote Multi
post #3 of 8
6 days, 23 hours ago
Thread Starter
- bishgeo
-
- online
- 28 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
$225 could not find any scrap. Just ordered these hinges for lid and fire box.
ReplyQuote Multi
post #4 of 8
6 days, 12 hours ago
- gary s
-
- offline
- 3,949 Posts. Joined 1/2011
- Location: Whitehouse, TX (East Texas) just South of Tyler
- Points: 84
I like those hinges, how much were they and where did you get them ?
Gary
"Ask and it will be given to you; seek and you will find; knock and the door will be opened to you. For everyone who asks receives; he who seeks finds; and to him who knocks, the door will be opened.
ReplyQuote Multi
post #5 of 8
6 days, 11 hours ago
Thread Starter
- bishgeo
-
- online
- 28 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
http://www.ebay.com/usr/randpcarriages $9,00
ReplyQuote Multi
post #6 of 8
6 days, 10 hours ago
- Dockman
-
- offline
- 356 Posts. Joined 6/2013
- Location: Climax Springs, Mo
- Points: 18
Seems like a really good price for pipe.
ReplyQuote Multi
post #7 of 8
6 days, 10 hours ago
- Maple Sticks
-
- offline
- 175 Posts. Joined 1/2013
- Location: Michigan-Florida
- Points: 19
My experience its the cuts that are expensive. Did they break the cost down? Steel per LB and charge for cut?
Not a reverse flow, No tuning plates, Not even a fire box. Just good Q
Its not what you use, its how well you use it. Smoke On
ReplyQuote Multi
post #8 of 8
6 days, 5 hours ago
Thread Starter
- bishgeo
-
- online
- 28 Posts. Joined 3/2014
- Location: springfield oh
- Points: 10
No just price for pipe cut to length.
smokejumper
Smoking Fanatic
OK, that was painful to read.
I'm sure it will be a lot smoother going forward though.
That piece of pipe is going to make a great smoker.
A good investment.
I'm sure it will be a lot smoother going forward though.
That piece of pipe is going to make a great smoker.
A good investment.
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.
Similar threads
Hot Threads
-
Painting Vinyl and Aluminum
- Started by Gonna Smoke
- Replies: 34
- Blowing Smoke Around the Smoker.
-
Recommend Outdoor Propane Fryer?
- Started by Count Porcula
- Replies: 33
- General Discussion
-
Featured Smoked Chuck with a braise finish
