120 gal. build -New Member-

Discussion in 'Reverse Flow' started by locovet, Apr 20, 2015.

  1. locovet

    locovet Fire Starter

    Hey guys started mine and my buddies build a couple weeks ago. Making good progress.
     
  2. smokejumper

    smokejumper Smoking Fanatic

    Welcome locovet,

    Yep, that is one gaping wet rusty nasty tank you got there. The finest smokers start from such humble beginnings!

    Looking forward to watching this build come together.
     
  3. locovet

    locovet Fire Starter

    Firebox so far. Will be finishing it up on Saturday.
     
  4. locovet

    locovet Fire Starter

    Will it be ok to use a larger diameter and longer chimney stack than what the calculator calls for? I already have a 6" pipe?
     
  5. lendecatural

    lendecatural Smoking Fanatic

    Should not be a problem at all, just make it a little bit shorter, not much under 30".
     
  6. locovet

    locovet Fire Starter

    Ok. Thanks. My buddy ran the calculator on his computer yesterday and I will post the results when I get them just to double check them before we cut out for the firebox.
     
  7. locovet

    locovet Fire Starter

    Here is the #'s from the calculator. Does this look right to you guys?
     
  8. locovet

    locovet Fire Starter

    Got the door mounted today.
     
  9. Looking good!
     
  10. locovet

    locovet Fire Starter

    Thanks cracksmoker I am watching your build as well.
     
  11. locovet

    locovet Fire Starter

    We are going to try and drop off the tank this week to get it sandblasted. We also cut the 3 upper door drafts. We are going to use the screw down type like you see on older wood stoves.
     
  12. locovet

    locovet Fire Starter

    Did anyone get a chance to look over my calculator #s just to double check for me? This is our first build and input would be much appreciated!
     
  13. smokejumper

    smokejumper Smoking Fanatic

    I try not to weigh in on calculations, but some of the other members should be along to help you out.

    Weekends are a busy time for most folks, so they may not be able to respond right away.
     
  14. daveomak

    daveomak Smoking Guru OTBS Member SMF Premier Member

    You should contact Gary and ask him.... It looks like the firebox vent opening are incorrect to me, but I don't know what goal he had in mind....

    It appears the upper and lower inlets are reversed.... the lower should be the larger number and the upper, the smaller number... the upper air inlets bleed small amounts of air into the CC for temp control and moving heat from the FB to the CC.....

    Total sq. in. opening, for the FB should be around 30 sq. in. I suggest ~20-30% upper air inlet and ~80% lower air inlets... I'm not sure what "high" and "low" designate....

    Below is my calculator/tutorial... it is a "manual', crunch your numbers... I know it is correct...

    http://www.smokingmeatforums.com/t/...ak-and-others-ready-to-use-rev-4#post_1264161
     
    Last edited: Apr 27, 2015
  15. Thanks for bringing that to my attention, I have told everyone it it still not complete and i have a few thing to correct and add.

    But I appreciate you letting me know

    Thanks

    Gary
     
  16. daveomak

    daveomak Smoking Guru OTBS Member SMF Premier Member

    Are the air inlets reversed ???? Look at locovet's FB door in post #8....
     
  17. Yes,  I PMed him and told him You caught that and I was correcting the reversal on the calculator. Also apologized for the mistake in the reversal.

    Told him at this point to cut the hinges loose from the door turn the door where those vents were on the bottom and re-weld the hinges

    Thanks Dave

    Gary
     
  18. Thank you locovet for being understanding.   I corrected that issue an will work to get it finished.  I wanted to make an easy to use RF calculator for anyone wanting to build a smoker. I want to make it the best it can be.  Members reading this are welcome to give me input. It is in an excel format and I realize not everyone can open it up. Maybe I can fix that as well.

    I'll be looking forward to watching your build as it progresses.

    Gary
     
  19. locovet

    locovet Fire Starter

    Not a problem gary. We are going to keep the top vents like Dave said but probably only end up using the middle one. We still haven't cut the bottom drafts yet so we are ok there. Thanks for looking and checking over.
     
  20. joe black

    joe black Master of the Pit OTBS Member

    Gary, at least you could go up and help him correct the openings. After all it's not that far from East Texas to Oregon. Since everybody is reading this, let me thank you for all the help you have given me. It's hard getting started on the right track with a new forum and it's folks like you, with all of your experience who make it enjoyable. Joe
     

Share This Page