Toggle sidebar

Recent content by bikerbob

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. bikerbob

    Masterbuilt problems

    Nothing special. Place the links on the racks and smoke till internal temp is 165 ( just for saftey sake) Living in Canada and presently dealing with cold and rain; not to mention covid lockdown. Where do you put your time in
  2. bikerbob

    Masterbuilt problems

    Thanks for all of your helpful advice; intend to smoke some precooked sausage for a trial run Results to follow Bikerbob
  3. bikerbob

    Masterbuilt problems

    OK after taking the burner off and blowing out with compressed air; found some corrsion bits. Then took a side grinder to the burner inlet holes and opened to slots and made a homemade shutter for control Reassemble and giving it a dry run; nice blue flame after adjusting the shutter and can...
  4. bikerbob

    Further Masterbuilt Problems

    Sorry for not getting back to your prompt reply; family got in the way I have attached 5 photos First is the junction of the gas nozzle and burner stem; as can be seen there is no adjustable shutter to control the mix. Second is of the smoker a Masterbuilt XL Third is the new adjustable gas...
  5. bikerbob

    Masterbuilt problems

    Sorry for not getting back to your prompt reply; family got in the way I have attached 5 photos First is the junction of the gas nozzle and burner stem; as can be seen there is no adjustable shutter to control the mix. Second is of the smoker a Masterbuilt XL Third is the new adjustable gas...
  6. bikerbob

    Further Masterbuilt Problems

    Getting a yellow flame not blue on my Masterbuilt smoker. Does not appear to have a shutter to adjust the oxygen mix. Has anyone else had this problem and what was your solution. Has anyone retro fitted a 3rd party burner to the Masterbuilt Bikerbob
  7. bikerbob

    Masterbuilt problems

    Good day gents I am still rather new to smoking Have an older masterbuilt smoker and have always had trouble getting temp down to 225. I have placed needle valve in the line which helped some. Planning on changing the regulator and would appreciate advise on required pressure. Any other...
  8. bikerbob

    Masterbuilt problems

    Good day gents I am still rather new to smoking Have an older masterbuilt smoker and have always had trouble getting temp down to 225. I have placed needle valve in the line which helped some. Planning on changing the regulator and would appreciate advise on required pressure. Any other...
  9. bikerbob

    First pork Ribs

    Have a question with regards to the 3-2-1 method of doing ribs I have read a number of the posts which state that the first 3 hrs smoker temp to be 225; does this also apply to hrs 2 and 1 thanks for your thoughts
  10. bikerbob

    How to get low smoke temps

    Thanks Fellas Looks like a needle valve and Amaz-n-smoke are in order
  11. bikerbob

    How to get low smoke temps

    Thanks Chef I was also thinking needle valve and have an inquiry into Bayou Classic Valve With regards to the pellet smoker; would you know it they take the same pellets as the pellet stoves?
  12. bikerbob

    How to get low smoke temps

    Hi Guys I have the Masterbuilt XL smoker and have major troubles getting the temps down to 120F for smoking Jerky I am using a cast iron fry pan for the wood tray and hickory chucks for wood My problem seems to be two fold First to get the temp down to 120 I need to leave the door ajar about...
  13. bikerbob

    Need Regulator advice

    Good day guys I am using a standard 20 Lb propane tank and wish to purchase one of Bayou Classic's needle valve regulators. They offer three units as follows 10; 20 and 30 PSI regulators Which should I order? bikerbob
  14. bikerbob

    Cures

    Thank you for the reply; it clears up a number of questions I gather that the best solution is to use the cure called for in the recipe Bikerbob
  15. bikerbob

    Cures

    It appears that there are three common cures in use Insta cure #1 Mortons Tender Quick Cure #1 Rather than having three cures an hand to make various recipes is there a formula for substituting one of the above for another Thank you for your help Bikerbob
See more
Top Bottom
Back
Clicky