New Yoder YS640 Just Arrived...in CT

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

smokingrk

Smoke Blower
Original poster
Jan 17, 2013
92
11
New Haven CT
After a long wait and some research, pulled the trigger on the Yoder

it arrived in the mess of wet snow and sleet ...but then the sun came out 


Uncrated and not a scratch on it  -


All parts inside wrapped nicely


Taking it off the pallet by myself was not easy but used some boards removed from packaging...

Our dog Java helped ,looks like he's saying I'm smelling something cooking. 


First mod was wheel change, there was no way the original wheels were making it thru

our grass and hill


Easy change


Wanted to point out that the seams on the door and contact seal is almost perfect.

Great job in assembly and welds



Grates installed and ready for burn-in


Did the burn in, added bacon as first cook to season...



Removed heat deflector and left side grate and add grill grates, fired it up to 600 F


12 min later steaks went on...





Finally dinner...timed it from lighting to dinner plate 35 minutes! steak had great flavor with touch of smoke, as did the asparagus

and added it all to some tortellini...


Apologies did not take shot of steak after cutting.

Will post next mod for temp probes, tomorrow or Saturday. 

Anyone in Northeast have a good distributor for wood pellets? 

Ordered some on line but shipping basically doubles the price. 

Hope you enjoyed the pics!!
 
The Port Mod -

Found ports here  or  - they are the same, I ordered both - the turned out to be same - one was a much better price. 

Things to Note - you need a step drill or about a 3/4" drill - use step drill if possible .

What I used:


The internals of the port are NOT for high heat so I replaced with woven (cloth like) Fiberglass sleeve, kept it in using a 1/2 inch copper pipe nipple about 3/4" long -placed inside the fiberglass sleeve applied high temp silicone to fib. cloth (only where it will make contact on inside of port aka cable gland) then into opening of port, pinching the cloth to the wall of port. Make sure that copper pipe length allows cap to be replaced. The cloth can be collapsed by a small clamp to keep probe wires in place and prevent airflow out (little anyway) via port - do not overtighten if used. Mounting was just below the top shelf rail as was recommended by others and towards the front on right side. I'm only mounting 1 port that can handle at least 4 probably max of 6-8 probes (based on my probe wires)
Original assembly:


Remove rubber grommet. Remove internal plastic sleeve replace with copper and fiberglass.


CAREFUL - Make sure the length of this port and fiberglass sleeve allows for probes to enter or if you have removable ends, then no issue. I use MAV 732 so my ends do not remove.

My current version - need to "pretty" it up by cutting fiberglass fabric back, added too much silicone to end and painted black since fib cloth was white :




Ultimately looking like this with small length of fiberglass sleeve protruding enough to clamp.


Hope this helps-
 
Started my first smoke on the yoder with three pork butts last night Fired up the smoker at around 9PM it was very cold out, about mid 20s F.

After coming to to temp, set it for 185F.  Waiting for the rub (all night before):


Meanwhile had the three little piggies all rubbed down with a basic rub recipe, one with a slight change in the recipe adding more ancho

and chipotle powder combo with more deep red paprika. Rub On:


On they go 10PM - don't have AMNTS tube yet so used AMNPS -seemed to work OK after I found the right spot for it.

At about 12:30 set temp to 225F and went to bed, after setting the MAV alarms on food and temp probe (just in case!!)


5:30AM - So 6+ hours later they are looking really nice (note AMNPS still going, filled only two lines!):


8:30AM - from left to right temps 199F, 189F, and 194F - seems it is going faster than I am used to with electric, though it is for learning on the
Yoder!


And a few close ups:




Can't wait to try, bringing two of these to a B'day party tonight. I'll try to get finished product here later. 
 
Wow...nice post Grk!
Looks like you got bit by the bug pretty hard. I'll bet you Ferraros is happy you got the Yoder. Best of luck with the new smoker and pray we get out of this weather pattern pretty soon or I'll be smoking in the Carribean.
 
Last edited:
Wow...nice post Grk!
Looks like you got bit by the bug pretty hard. I'll bet you Ferraros is happy you got the Yoder. Best of luck with the new smoker and pray we get out of this weather pattern pretty soon or I'll be smojing in the Carribean.
Carribean Smoking huh?! 
grilling_smilie.gif
  We'll have to explore that..its pretty mild out this AM been up early with the pork, much better than last night when I started it was probably in mid 20s.

Thinking of Pizza for tomorrow, so Ferraros will have to wait till next week.

This is much more enjoyable than what I had to deal with before, all temps held within 8-10 degrees across the smoker.

Waiting for the last butt sitting at 198 now for the last 2 hours, the other two smaller ones are resting, pulled them at 205. 

Time to finish on the other two butts was about 12hrs @225 they were about 7.5 lbs each.  - faster than I expected. 
 
OK the finale for today - so pulled the last butt off at around 205 @15.+ hrs its bizarre how similar size and weight just sometimes finish much later.
So here they are, apologies for out of focus did not notice till upload...




After a nice long rest:


The bark was amazing, best I've had in a long while.


YUM!!! So far very pleased with the cook and the flavor. Hopefully friends at the B'Day will enjoy ...
 
Sharing a Fatty and some rib Views...  Ground Pork and Sausage, Sauteed onions and garlic, fresh Jalapenos,

sliced ham, provolone, cheddar, mozzarella and a handful of grated Parmesan. 


Baby backs with a Moroccan dry rub, heavy on the cinnamon...


Finished products,





hope you enjoyed the pics...
 
Way to go grk, Great photos, getin right into it. Got the mods done first thing. Then on to Quein. Way to go!!!

I can smell the smoke from here, No waite that is mine on the deck.

According to UPS tracking my wheels will be here to day.

Suggestion, When smoking several cuts of meat. place the largest cut closest to the fire. At the 8:30AM check,

place the cut with the lowest temp. at the hot end.

Did you get the nylon sleeve at Amazon too?
 
Last edited:
Way to go grk, Great photos, getin right into it. Got the mods done first thing. Then on to Quein. Way to go!!!

I can smell the smoke from here, No waite that is mine on the deck.

According to UPS tracking my wheels will be here to day.

Suggestion, When smoking several cuts of meat. place the largest cut closest to the fire. At the 8:30AM check,

place the cut with the lowest temp. at the hot end.

Did you get the nylon sleeve at Amazon too?
Thanks for the suggestions. By keeping the YS640 VDD (damper) about halfway (with some tweaking during the cook) I am able to stabilize temps on bottom and top racks. By setting the temp to say to 225* I can keep the bottom rack around that temp and the right side top rack gets to about 10*-15* higher. That is why I placed the flat on top and the lamb and ribs on bottom racks. Still learning the pit so stay tuned...

As for the wheels (16" side) one thing I did not post is that I also used a 1/2" solid axle all the way across,making it a bit more stable. I used small cotter pins on the outside of each wheel, with 1/2" stainless washers on both inside and outside wheel bearing surfaces, so make sure when you measure you take those into consideration, along with the width of the wheel bearing, if you go down that path.

Not sure what nylon sleeve you refer to? If you mean the probe port, those are stainless,  I removed the internal nylon sleeve and replaced with 1/2" copper tube with the inside of the copper covered with fiberglass sleeve to offer some level of heat protection,although most good temp probes have cables that withstand high heat.  Link to where I found the ports is at the top of that post.  Let me know if you meant something different. 
 
You did replace the two axe's  with a solid one. The local big box store has the 1/2" rod in 3 ft length, so there is plenty of length.

My thought was to use the two pins on the outside ends to hold the axel in place,  

Yes, I meant the fiberglass sleeve.  

The UPS tracking number I had was for the caster wheels.

So they arrived yesterday. Still waiting for the 16" wheels.

Can you post a close up photo of how the castor wheels are mounted. 

What is the screen you have between the meat and the grill grates?

Looks like a good idea to help keep the grates clean..
 
Last edited:
I drool every time I see the Yoder.  I would like to get one but I am really concerned about pellet consumption.  In your 15 hour smoke, how many pounds of pellets did it use?  Is it fairly easy to clean out the ashes?

Thanks.
 
Pellet consumption depends on ambient air temp,wind and cooking temp. At 225 - 250 cooking temp consumption is about 1/2 to 3/4 lb per hr.

I think cleaning is easy. clean the grates with a wire grill brush wipe with cooking oil. Wrap the drip pan in foil replace the foil from time to time.

I have a small wisk broom and dust pan about 6"wide to sweep up most of the ashes. Then use a shop vac to clean the nooks and crannies.

Then don't forget the small bucket to catch the grease.    
 
I drool every time I see the Yoder.  I would like to get one but I am really concerned about pellet consumption.  In your 15 hour smoke, how many pounds of pellets did it use?  Is it fairly easy to clean out the ashes?

Thanks.
Quick removal of the grates and heat diffuser (drip pan) I remove the ashes with a shop vac. Really easy from my perspective. 

For the pork butts not an exact measure but about 24Lbs of 20lbs Lumberjack / 4lbs BBQ Delight at about 15.5 hrs so a bit over 1.5 lbs an hour. Not bad considering no blanket and temp outside was in the mid 20s when started in the PM and went overnight, did get milder in AM though.
Pellet consumption depends on ambient air temp,wind and cooking temp. At 225 - 250 cooking temp consumption is about 1/2 to 3/4 lb per hr.

I think cleaning is easy. clean the grates with a wire grill brush wipe with cooking oil. Wrap the drip pan in foil replace the foil from time to time.

I have a small wisk broom and dust pan about 6"wide to sweep up most of the ashes. Then use a shop vac to clean the nooks and crannies.

Then don't forget the small bucket to catch the grease.    
As Ollie says it is very dependent on on many things (add to the list "meat" load) - What I've experienced now for the last few weeks as Ollie, the Yoder uses from 3/4 to 1.5 lbs pellets /hr. on average between 180* and 245*F. With that said many claim Yoder pellet use is more than some other cookers, however I bought mine for overall performance and quality than just pellet use.  Now if you want to see some additional pellet efficiency and spend some extra $$ look at the YS1320 - with a recessed fire box etc. 
 
You did replace the two axe's  with a solid one. The local big box store has the 1/2" rod in 3 ft length, so there is plenty of length.

My thought was to use the two pins on the outside ends to hold the axel in place,  

Yes, I meant the fiberglass sleeve.  

The UPS tracking number I had was for the caster wheels.

So they arrived yesterday. Still waiting for the 16" wheels.

Can you post a close up photo of how the castor wheels are mounted. 

What is the screen you have between the meat and the grill grates?

Looks like a good idea to help keep the grates clean..
Sent you a PM - Exactly what I did two pins on the outside of each wheel, which is why I recommended to use washers between inside and outside wheel bearing surfaces. As for the fiberglass sleeve (really a cloth of fiberglasss) I had it from years back when I worked on high temp devices. Search some high temp oven / element stores online, if you cannot find readily, PM me with an address and I'll mail you a piece.

The casters require you to drill out the existing hole with a 5/8" bit. Careful as it twisted and bound on me almost took my wrist out, I used a straight metal bit, but if you have a step bit it would be easier, careful not to overshoot. Also you will need about 8 to10 5/8" washers and 2 nuts (M-14 or 15 can.'t remember) I used lock nuts so did not use lock washers - you can find both these at HD or Lowes , bring a caster with you to try nut for fit. 

The screens as you called them on the grates are called a Q-Matz or Frog Mats.  Todd, from Amazing Products ( a site sponsor) sells these in two widths by the foot http://www.amazenproducts.com/SearchResults.asp?Cat=46  .   They work well with small or sticky type cooks. 
 
That smoker looks like the bees knees!!! Along with the cooks in rapid succession it seems. I can't blame you. Beautiful smoker. Have you talked to Todd about buying pellets in bulk? Right now I currently use traeger pellets that can be bought at ace hardware in 20lb sacks for about $17.
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Hot Threads

Clicky