Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. killerb468

    Compressor tank to a backyard smoker

    I will be on it around Thanksgiving. I will start a new build thread.
  2. killerb468

    Compressor tank to a backyard smoker

    I will be starting it around end of july.
  3. killerb468

    Compressor tank to a backyard smoker

  4. killerb468

    Compressor tank to a backyard smoker

    I mentioned above I needed to keep the stack short due to enclosed trailer. This easy on and off extension does not leak. So I won’t weld the collar to the extension. Easy to remove and stire.
  5. killerb468

    Compressor tank to a backyard smoker

  6. killerb468

    Compressor tank to a backyard smoker

    I did cut the old stack out and put a 4 1/2” diameter stack. Had to keep the stack short to get it into my enclosed trailer. I made a 15” extension so it is 36” above cc. Here is a ouc without extension. Did a run last week and the week before. Door is all sealed and can go from 150° to 400°...
  7. killerb468

    Compressor tank to a backyard smoker

    Been almost 10 years i have made a few changes and today i changed out the smoke stack. Long story short I have dealt with a leaky (not bad) cc door. So a few weeks back decided to seal it off. And low and behold I could not get the CC above 165°. Cut and scraped the seal off as I was at a...
  8. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Digging this build, here is Frankenstein… I have cut i to it several times since building it 8 years or so ago. Getting ready to out a new stack on it. Glad I didn’t paint it. I like the rusty look.
  9. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Look forward to seeing the progress
  10. killerb468

    Burger Brawl Voting Poll....Some Amazing Entries!! (Pretty Long)

    Great batch of entries right there.
  11. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Yea I meant FB, are you going to make it 1 rack or 2?
  12. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Nice build you have going. I built one years back. I am about to start another build. What size DB did you go with? I am going to run a 24” x 24” FB on my 24”x 46” tank. Keep up the solid work.
  13. killerb468

    Tine to build another smoker

    So I an passing on the tank. Should I look for another one or just raise the roof and have a split door on my old smoker. Cut and raise 4 or 6”. I believe I have seen it done on here. Could find the thread.
  14. killerb468

    Tine to build another smoker

    I haven’t seen it yet to lnow if it is galvanized or not. How would you know if if is glass lined? Also is there a scratch test gor galvanized propane tanks? Might be better to mod my existing smoker and add 6” to it for another rack. Here is the freak, built 10 years ago. Still doing work.
  15. killerb468

    Tine to build another smoker

    I was given this tank and before I put time into it. Will the center weld seem be an issue other than cosmetic? Don’t want it to do funky stuff when I cut it open. Measures to be a 125 gallon and want to make a horizontal RF out of it. Please, any thoughts would be appreciated.
  16. killerb468

    Cleaning OK Joe or any offset smoker

    I have a grease drain on my RF plate, I am referring to grease runningbdown the end and under the RF plate.
  17. killerb468

    Cleaning OK Joe or any offset smoker

    Few weeks back, I was cleaning my smoker, I reached in and under the RF plate thru the CC. I stuck my hand in a puddle of grease, I got as much as I could with paper towels. What is the best way to clean under the RF plate when it is welded in? Should I add a grease sump and drain to the bottom...
  18. killerb468

    20" Pipe RF Smoker

    Your build has so much WIN!!! it is simply sexy. And that bacon jerkey if off the hook, did you back it covered or right into the oven after seasoning?
  19. killerb468

    It has begun

    thats what I did on a converted 14 bolt full float axle for a trailer. Pulled the bearings and packed it full of grease.
  20. killerb468

    Naming your smoker...

    I have a buddy that is going to cut my name plate out on his plasma table... I am incorporating my nick name into the smoker name. The name of my smoker is KILLER"B"bq
Top Bottom
Back
Clicky