Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. Arapaho G

    Auber WS-1510 Not Reaching Temp

    A few days ago I smoked a pork butt. This was my first attempt since the turkey breast that started this thread. I took some of the suggestions that were presented here, and I am happy to say that the Auber worked perfectly. Here's what I did: I changed the settings to match Chopsaws. I wrapped...
  2. Arapaho G

    Auber WS-1510 Not Reaching Temp

  3. Arapaho G

    Auber WS-1510 Not Reaching Temp

    The sensor was middle left side about 1/3 down from the top. PID settings are standard factory settings. The turkey breast was 5.3lbs raw weight. I removed the skin and injected 1 1/2 cup of chicken broth, butter, and spices. There was about 2/3 cup of liquid in the bottom of the pan that I...
  4. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Thanks for all your responses guys. My next attempt will be to try a different circuit and make the settings adjustments to the Auber and see what happens. I think I will also set the control at 260*. I'll let you know how it goes.
  5. Arapaho G

    Auber WS-1510 Not Reaching Temp

    I believe the next thing I'm going to do is determine how the meat effects the temp inside the box. I now have a situation where the smoker is holding 270 degrees +/- 2 degrees when empty. I'm thinking that I may only have to regulate when I need a lower temp (for salmon or other low temp apps)...
  6. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Yes sir, that's exactly what I did.
  7. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Yes I can access the connections. When I replaced the element I also put new stainless connections on it too. I will have to take the covers off and double check my work, but I'm 99.5 % that the element is wired directly to the plug. I also believe that it can get hotter, but the only...
  8. Arapaho G

    Auber WS-1510 Not Reaching Temp

    20 amp circuit with no other draw besides internet modem.
  9. Arapaho G

    Auber WS-1510 Not Reaching Temp

    The electric cord with plug is wired directly to the element. MES electronics have been bypassed. I have been watching this for about 1/2 hr now and it is maintaining 270 +/- 2* with no controller at all. Just plugged in directly. Strange.
  10. Arapaho G

    Auber WS-1510 Not Reaching Temp

    So... there is a limit switch on the burner itself?
  11. Arapaho G

    Auber WS-1510 Not Reaching Temp

    So this is interesting. As I said earlier, the heating element is wired directly to the plug. I plugged it in and put my ThermPro sensor directly in the middle of the box. It took about 30 minutes for the temp to rise to 282, outdoor temp in Golden Co today is 47. Then it started dropping, as if...
  12. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Easy enough to do. The element is wired directly to power in the smoker so all I have to do is plug it in and let it go. I performed this test right after I rewired the smoker but I did not measure the temp, only that it was on and getting hot. I'll plug it in and measure and report back.
  13. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Yes you are correct that the set up performed "better" with the box empty. Better, but not accurate. It did reach a higher temp, but not the set temp, and it did not hold it. It was set at 275. Empty it went up to 272, then dropped to 265, and continued dropping to 260. At that point I shut it...
  14. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Thank you for the settings. Yes, you are correct. I don't have a real understanding of how these controllers work. Some research is in order. I was expecting a plug and play operation, but the controller is so versatile it has to be configured to your specific application. In our case, smoking...
  15. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Thanks. I have the same smoker so your settings should be about what I need. Sounds like something you have to get a feel for. I was hoping for a set it and forget it. This turkey will be consumed today so I'll be doing another later this week to try it again.
  16. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Thank you for this. Shortly after I wrote the post, I pulled the turkey out of the smoker and put it in the oven. It had already smoked for 2 hours so I wasn't worried about smoke flavor. It's finishing in the oven so I can dial in the settings for the next time around. Any other settings...
  17. Arapaho G

    Auber WS-1510 Not Reaching Temp

    Here comes another question about the Auber controller. I'm guessing this gets talked about a lot here and if so, sorry to be redundant. I have used my WS-1510 5 times now and the performance has been less than stellar. This may be because of something I'm doing wrong or maybe there is an issue...
  18. Arapaho G

    Smoking a Jennie-O Without Skin

    Today was the day. All went well and it turned out great! Moist and juicy. I smoked at 250 until it reached 260. Took it out and covered with foil. Dinner tonight, but I had to sample it. Very tasty indeed. This was also the maiden voyage for my new Auber universal controller, new A-Maze-N 12"...
  19. Arapaho G

    Smoking a Jennie-O Without Skin

    Thanks guys for all your responses. I've decided to inject, and then smoke at 250-275 in a pan containing chicken broth and butter. I'll use a dry rub and then baste as I go. Hopefully it stays moist without the skin.
  20. Arapaho G

    Smoking a Jennie-O Without Skin

    Hello All, I will be smoking a store bought Jennie-O enhanced turkey that already contains an 8% solution of turkey broth and salt. I want to do this skinless so that has me a little confused. I want to brine and inject to keep it moist. I have looked all over the internet about this and find...
Top Bottom
Back
Clicky