Recent content by hjbct

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. hjbct

    Cure chamber build questions

    A small aquarium pump (air bubbler pump) on a timer will work. My chamber has similar sized holes and works fine - just stick it on a timer. You can estimate how long it takes to replace the volume of air in the fridge and decide how often you want to do that. Having said that, from what i...
  2. hjbct

    Curing chamber heater

    Like you, I use a seed heating pad. I ended up with two which is fine for my small fridge. Personally, I like the idea of using low wattage heat, rather than blasting with higher wattage - maybe use more pads? With a higher wattage heater, I would imagine you will see bigger temperature...
  3. hjbct

    Hi - any progress with your Raspberry Pi?

    Hi - any progress with your Raspberry Pi?
    • hjbct
    • Profile post
  4. hjbct

    PorkPi - Latest batch

    I'd be interested to hear how you get on with the lag and overshoot (hysteresis?) with you code - i'm looking for a better algorithm.
  5. hjbct

    PorkPi - Latest batch

    I may look at that sensor - I see Adafruit has Pi library for it.  I think my DHT22 has been unreliable for humidity - I bought a second but never got around to replacing it.   You should be able to change the python code to use that sensor pretty easily. BTW, there are better algorithms for...
  6. hjbct

    PorkPi - Latest batch

    I've posted the code on Github. I'm afraid it is not very well documented but happy to help.  I have not put up a wiring diagram, so this is certainly not a recipe for how to build the system, but may be a jump start for someone. I don't know how to put up the google sheets on Github, but the...
  7. hjbct

    PorkPi - Latest batch

    sure - let me look at getting some stuff up on github.
  8. hjbct

    Raspberry Pi Temperature Remote Monitoring

    Fun project.  I've built a chamber controlled by Raspberry Pi - works well.  Python code on the Pi and Google Sheets as the GUI. Checkout this earlier post! http://www.smokingmeatforums.com/t/252528/porkpi-latest-batch
  9. hjbct

    Fluctuating temperature and humidity - is it a big problem?

    I have not found fluctuation a problem as long as average over 1 hour is good.  I'm seeing +-15% on RH with my setup.  Temp seems easier to keep tight, but still +-5 degrees.  My averages are where i want the target RH and Temp to be.
  10. hjbct

    My adventures in starting dry curing

    Nice!  Following this with interest,  I wish my fridge was bigger!
  11. Capture2.PNG

    Capture2.PNG

    • hjbct
    • Media item
    • Comments: 0
    • Album: PorkPi - Latest batch
  12. hjbct

    PorkPi - Latest batch

    Here's the parameters page.  This allows me to manage hysteresis.  Circ fan is inside the fridge.  Air pump is aquarium pump which injects air. This is the drying schedule - allows a daily change in Temp and RH.
  13. Capture2.PNG

    Capture2.PNG

    • hjbct
    • Media item
    • Comments: 0
    • Album: PorkPi - Latest batch
  14. Capture1.PNG

    Capture1.PNG

    • hjbct
    • Media item
    • Comments: 0
    • Album: PorkPi - Latest batch
  15. Capture.PNG

    Capture.PNG

    • hjbct
    • Media item
    • Comments: 0
    • Album: PorkPi - Latest batch
See more
Top Bottom
Back
Clicky