Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I do notice that it does overshoot by 1 1/2° Once I open it So I may have to call them and see which setting I need to change
  2. ryans01z28

    Fine tuning Mypin PID T-Series Question

    No that was not it. There was one setting I had to increase the value by one number or something like that I can’t remember I changed a couple things and it works now. On my Other PID I had to hold the set button for the auto tune and for some reason I thought I had to do the same thing with...
  3. ryans01z28

    Fine tuning Mypin PID T-Series Question

    So now that I have the the auto tune going to the settings that you posted the temp has dipped to 93.7 as of now and the out put light flashes every 1 second but he temp is still dropping. I have never had a problem as big as this one with my smoker pid. What’s going on? It shouldn’t dip that...
  4. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I have it in auto tune right now and the temp has dropped all the way to 90* and hasn’t fired my heater one time with the settings I have in my above post. I will try yours now. My I- only goes to 0002 not 0
  5. ryans01z28

    Fine tuning Mypin PID T-Series Question

    It was in auto tune then but I changed my settings as you can see in the next few post. It’s over shooting up to 105* now. Wtf
  6. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I’m not in auto tune right now I’m just trying to get it stable then I’ll auto tune it??
  7. ryans01z28

    Fine tuning Mypin PID T-Series Question

    So right no I have it set like this P-9.5 I-0 D-0 It starts to heat at 99.3 and Shuts off at 100.6. That’s hotter than I want. I need it to stay 99.5. I know it can do it I just don’t know which setting to change.
  8. ryans01z28

    Fine tuning Mypin PID T-Series Question

    Ok so when it’s in auto tune now and it drops below the set temp the light doesn’t flash. It’s 2* below the set temp at the moment and it hasn’t kicked the heat on yet. What setting is that? Is that the D setting? There’s not a lot of air coming in or going out. 1/2 hole on one side and 1/2” on...
  9. ryans01z28

    Fine tuning Mypin PID T-Series Question

    Right. I did that all ready but they were closed already
  10. ryans01z28

    Fine tuning Mypin PID T-Series Question

    Right now I have p-1 I-default (100) D-30 and it’s holding ok. I’m going to try auto tune unless you think that’s not what I should do.
  11. ryans01z28

    Fine tuning Mypin PID T-Series Question

    Ok this is the info I needed last night. So I set my P-0 but it over shoots now so I need to change it to P-1 to get it tighter? I want this to hold as tight as possible to 99.5°. After I changed the setting like you said it shot the temp up to 102°
  12. ryans01z28

    Fine tuning Mypin PID T-Series Question

    No I don’t have one on there. It’s a 3 wire rtd thermocouple
  13. ryans01z28

    Fine tuning Mypin PID T-Series Question

    Somethings not right here this won’t keep temp where I want it to. Output light keeps flashing even after the target temp is exceeded
  14. ryans01z28

    Fine tuning Mypin PID T-Series Question

    My target temp is 99.5 and my mercury thermometer is up to 115* inside. I have it on auto tune now and the temp keeps climbing. It flashes on and off just like the other one I had. Why???when the temp is above the Target temp it shouldn’t be flashing at all until it drops below the target temp
  15. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I was kind of in a panic because I swapped my bad PID with another mypin PID and I couldn’t get my heater to turn on. So then I grabbed this other new one and hooked it up and had no idea how to set anything on it so while I had the wife nagging at me and one of my kids trying to talk to me it...
  16. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I am set at -14.8° On my offset that gives me my 32°F. I tried to do the boiling water but from the store over to the thermal coupler I could only get 182° out of it
  17. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I bought a new one when I bought this PID the other day. I am using a RDT thermal coupler know From auber
  18. ryans01z28

    Fine tuning Mypin PID T-Series Question

    OK I think I have the offset correct now. Shall I hit the auto tune button or are there other settings that I should adjust?
  19. ryans01z28

    Fine tuning Mypin PID T-Series Question

    I already have that done. I am just trying to get the offset right while it’s an ice water right now
  20. ryans01z28

    I need help with Auber syl-2362 fast

    I switched my PID controller In the middle of a run and I need help setting it up I have never used this type of pid before. I always had a MYPIN pid. I need help setting it up fast. I need to know how to set up the offset on it. Right now I have my temperature probe in Ice water and it is...
Top Bottom
Back
Clicky