Search results for query: Mailbox mod

One of the things with the tray is you really need to hit it with flame for about 5 minutes before blowing out the flame. The u-bolt mod has had great reviews. I went with the mailbox mod. And haven't had an issue since.

...have a 15 degree swing when first turned on but over a little time it settles in and maybe I get a 5 degree swing. Also check out the mailbox mod, works great for cold smoking or longer smokes with continuous smoke for 9-12 hours. I also have a pellet smoker/grill but in my opinion the mes...

Thank you for your responses. I am not familiar with the mailbox mod, but just by looking at the pictures I am assuming that the mailbox is a separate smoke generating chamber. The box holds a tray or a tube that holds pellets or chips, and then said pellets or chips are started manually with a...

Mailbox mod and or a pellet tube/maze will have you covered!

That's the gist of it. You may have to tweak your mailbox mod with adding holes or covering up existing holes, etc. but that stuff is simple and is honestly just part of tweaking your BBQ setup/system to work for you and your situation. For instance I have my MES and mailbox mod in a plastic...

...has just the bite you want, a nice pop, so I don't think it is a problem with the casings. I have also tried a pan of water in the smoker. I am using a fridge smoker with a mailbox mod, that I built with a pid controlled 1500 watt heating element. Please give me an idea what I am doing wrong!!

Thanks! What is an MES?

Yes the mailbox mod is a smoke generator but with no heat source. I typically use the AMNPS tray that is slightly elevated off the floor of the mailbox. The mailbox floor has maybe 9-12 1/4" holes in the bottom. The door of the mailbox has 4 holes. Yes a 4" hole in the back which the duct...

I have an AW-1520H so it is 15A. I'll give those settings a shot and adjust where I'm putting my Auber probe and see how that effects things after my other tests just to make sure the smoker itself is functioning properly. I did make a new exhaust dead center in the top and my top probe always...

You start the pellets or chips manually with a torch, correct?

This is one of the reasons that I got a MES. Lookin for a cart/table for it to sit on.

Alright everyone, I’ve done it. After months and months of tinkering, I’ve finally achieved a nice smoke ring on ribs in my MES with mailbox mod!!! And no, I didn’t use curing salts. I considering that cheating, don’t know why. First off, I used the wet-dry method, but honestly I didn’t know...

Here's some examples of it on an MES the 1st two pics are actually my mailbox mod and you can see my AMNPS tray with pellets getting ready to be put in the mailbox mod in pic #2: Others: I like the ammo can style that is attached directly. Again these are mailbox mod ideas for MES and...

...router controller to plug it into. I use a 6" PVC coupling with a $14 sealed 4-D battery upside down camping tent fan as a draft on low. I use the mailbox mod with the cold smoking fan. You say dry it in the garage for hours or days. Your taking about in the fridge in the garage for days?

Glad you got it under control. I had a bad fire in my MES40 once. I put the pellet tube on the heat deflector which started the pellets on fire and starting the fat in the pan on fire. I pulled the pan out and grease on fire went every where. Man was that scary! Got me to do the mailbox mod.

I average 10 hours out of my original 12 " . They have a solid end cap , and I think that makes a difference in burn rate . I have the newer 6 and 12 . Both with holes in the end cap . With the U bolt I still get good burn times . Using a mailbox makes a difference too .

...I could either reduce the amount of smoke going into the Bradely, or increase the airflow. As previously mentioned, I have done the mailbox mod and I have a pellet tray. I also have the top vent fully open. The pellet trays sure spit out a lot of smoke. Granted, it's all relative of course...

How do you smoke your sausage? You mention the "sausage smoking process".

Mailbox mod was cheap < $30 since I already had a tube and maze for a year. With the Mes 40 on the leg kit I made a stand from a tomato cage and bolt cutters to raise the vent hole on the top rear of the mailbox to the same height as the chip loader 3" hole and secured with a shoe lace and...

...fish and products. Lots of people only do cold smoked bacon and it only gets heat or cooked when it hits the skillet. So basically a mailbox mod allows you to separate smoke generation from the MES heat generate and have greater control overall. Additionally if using the A-Maze-N Pellet...