Toggle sidebar

Recent content by golfpro2301

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. golfpro2301

    Overnight Brisky Cook

    I do a few hogs a year. One on 4th was 310 before processing. That was big mofo. Half cow or cow leg is on bucket list
  2. golfpro2301

    Overnight Brisky Cook

    Neighbor bday today so fired up pig pit. Ran overnight at 225 for brisket. Butts went on at 2 am. Smoker performing well. Controlled by FB drive with guru fan
  3. golfpro2301

    Whole Hog Gravity Feed Build

    Finally got finishing touches on. Right door slightly open which is why letters look off
  4. golfpro2301

    Whole Hog Gravity Feed Build

    Been a bit since the test fire. Made some changes to FB and transfer chute size. Decreased heat up time in half. finally able to get some color on it today. Used custom coat truck bed liner in bright purple. Daughter picked color. Plan on getting logos done tomorrow in Black. Also had a...
  5. golfpro2301

    Whole Hog Gravity Feed Build

    Alright. Its time for testing! Please start praying everything works right.
  6. golfpro2301

    Whole Hog Gravity Feed Build

    So so close to wrapping this up. Got everything stitch welded. Next is epoxy all seams to fully seal in and make everything smooth for paint. Had to upgrade rear end as original axle bent due to weight. Went from 2 to 6 bearings. Plan to make a removable motor mount in next week so I can get...
  7. golfpro2301

    Whole Hog Gravity Feed Build

    Yeah those are current latches. Id prefer a rotating compression latch
  8. golfpro2301

    Whole Hog Gravity Feed Build

    Anyone know where I can get hooks for this type of latch or what latch name is? This is off old myron mixon h2o smoker.
  9. golfpro2301

    Whole Hog Gravity Feed Build

    Better overall look without sun in way
  10. golfpro2301

    Whole Hog Gravity Feed Build

    More progress pics Got few outer skins on Water pan welded up with fill and drain holes Exhaust stacks tack welded and fit up. Will weld in later and build collection boxes around CC outlet to seal in.
  11. golfpro2301

    300 gallon Propane tank PELLET smoker build - Questions

    I have built and used a lot of pellet cookers and for this to work I think you would need a much longer auger tube to burn pot. You would likely need to have these enter into CC on lower back and sit the chamber into 3rds with burn pots under each line with diffuser plate. You could easily turn...
  12. golfpro2301

    Advice for an Offset Smoker

    How close to NE FL are you? Have a 250gal offset id be willing to let go.
  13. golfpro2301

    run away smoker

    On vertical type smokers using top vent is good way control temps. With the smoldering in charcoal pan the closure wont put dirty smoke on meat. #1 issue of runaway temps with controllers is excess air entering cook chamber thru fan. You need VERY little air flow to maintain temp. Cut fan...
  14. golfpro2301

    CAD logo Help Needed

    I am getting a logo made for the new cooker but need help taking from jpeg to dxf file and incorporating some edits. Anyone have experience with CAD who would be willing to help? Please DM
  15. golfpro2301

    Whole Hog Gravity Feed Build

    Finished out firebox and added in charcoal chute. Was also able get back gap wall in place just need add spacers at top. No more smoker work until next week.
See more
Top Bottom
Back
Clicky