Toggle sidebar

Recent content by fendbass22

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. fendbass22

    Gravity Fed Build

    Here is a screenshot of the dimensions. I am not a pro at CAD, I mainly use it to get the plasma cut outs I need to cut them out with my plasma table. I also get to a point where I can proceed with the build and stop messing with the CAD. The frame dimensions are correct but there may have been...
  2. fendbass22

    Gravity Fed Build

    A few more finished pictures... with my 4 year old breaking stuff. Good thing the chair was headed for burn pile anyway. Smoked a rack of ribs yesterday that came out awesome. Had temp set to 240F and held very nicely with fan at 30% speed. The issue was when I opened door to move some iGrill...
  3. fendbass22

    Gravity Fed Build

    I built a vertical reverse flow offset a few years ago and after a work competition where I tried to smoke 8 racks it became clear it was too small. I started looking into buying a pellet smoker for the convenience since I have two small kids. Then I decided to build a pellet smoker (first 4...
  4. fendbass22

    Mini Vertical Reverse Smoker Build Questions

    Hoping to get the 1x1" frame done then enclose it with diamond plate. See how it goes.
  5. fendbass22

    Mini Vertical Reverse Smoker Build Questions

    New gaskets work great. At the ends I just took about 6" piece of the gasket and folded in have to put about 3" in each end. Working great. As I suspected the thermistors would stop working as they weren't high temp rated. Adafruit sells thermocouple type-K breakout boards for Arduino so I...
  6. 20160724_122008.jpg

    20160724_122008.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  7. 20160710_200149.jpg

    20160710_200149.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  8. 20160724_074829.jpg

    20160724_074829.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  9. 20160724_074531.jpg

    20160724_074531.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  10. 20160710_102642.jpg

    20160710_102642.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  11. 20160703_105637.jpg

    20160703_105637.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  12. 20160703_105620.jpg

    20160703_105620.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  13. fendbass22

    Mini Vertical Reverse Smoker Build Questions

    Put some temporary door hinges on to try it out. I don't want to finish the outside until I know how it works. Burned it off at around 400F. Stack pic. Today I went to do some testing and the wife has a ham bone with plenty of meat and fat left to season it up. I figured I would wash...
  14. 20160626_205347.jpg

    20160626_205347.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
  15. 20160626_191956.jpg

    20160626_191956.jpg

    • fendbass22
    • Media item
    • Comments: 0
    • Album: Mini Vertical Reverse Smoker Build Questions
See more
Top Bottom
Back
Clicky