Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. nick344

    1st turkey

    Ok fellas here is my first turkey. I have lurked around the site for awhile when I was planning to build a smoker. I never got to build it. I used a weber 22.5 kettle. I used the slaughterhouse brine and injected it with Cajun seasoning. I used minion method with hickory and kingsford. It...
  2. nick344

    Smoker Parts

    See if you have an airgas around your area. It a welding supply type business. http://www.airgas.com/browse/productDetail.aspx?Category=292906&product=ATLAT29B
  3. nick344

    Smoker build

    After doing some research i think you are correct. The guy that gave it t me said it was a 100 gallon so i took his word. it was free so i will make due
  4. nick344

    Smoker build

    Thanks. Same for you. My problem is staying "motivated". I have had my tank for close to a 8 months and just now getting around to using it. I found some plate at a scrap yard in decatur it is a bigger piece then i need but  i am still thinking about picking it up,
  5. nick344

    Smoker build

    The calculation are very different.  Thanks solaryellow for the input in using volume .
  6. nick344

    Smoker build

    Honestly I have no reason. I have had the calculator saved on my computer and did not look at it before i did my measuring. I will look at it using the volume part of the calculator.
  7. nick344

    Smoker build

    Ok fellas I am finally in gear to build my smoker. I am planing on a reverse flow smoker. Take a look at my calculation and see if they seem correct. I have a 100 gal propane tank and got the diameter of the tank by using the formula d= circumference/3.14. Let me know if something needs corrected.
  8. smoker calculations.jpg

    smoker calculations.jpg

    • nick344
    • Media item
    • Comments: 0
    • Album: Default
  9. smoker calculations.jpg

    smoker calculations.jpg

    • nick344
    • Media item
    • Comments: 0
    • Album: Default
  10. nick344

    Reverse Flow Smoker Build!

    Thanks. I have not tried scrapyards yet. I was going to call around today. I figure that I am going to need somewhere around a sheet. I have a 100 gal tank so the firebox should not have to be that large. I will have to recalculate the size of it. I will have to check with the guy on ripely road
  11. nick344

    Reverse Flow Smoker Build!

    Looking good. Where did you source your 1/4in plate? I'm to the east of you in Athens. A few places I checked wanted a arm and a leg.
  12. nick344

    Newbie with a question.

    Thanks. I will get some 3/16 or 1/4. I am thinking of insulating mine with rockwool. What did you use? Will the 1/8 work for the rf plate?
  13. nick344

    Newbie with a question.

    thanks. I have done a lot of reading and took the e courses. I have been a member for a few months just dont post that much. All the builds I looked at I did not see where they talked about material thickness. I could have over looked it also.
  14. nick344

    Newbie with a question.

    I am finally getting around to building my RF smoker. I am using a 100 gal propane tank. I have used the calculators to figure out what size fire box, exhaust stack and air inlet sizes i need. My question is I have a piece 1/8in plate is that thick enough for fire box or does it need to be...
  15. nick344

    Another New guy here.

    Can you post a link to it. I am getting ready to start a build and it would come in handy for me.
  16. Default

    Default

    • nick344
    • Album
    • Comments: 0
Top Bottom
Back
Clicky