Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. 20150924_183509.jpg

    20150924_183509.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  2. 20150924_183502.jpg

    20150924_183502.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  3. racer102

    Newbie Here

    So it looks like square is better than round is that correct. Also the square inch calcs I take are based son sea level I'm at 5000 ft. Says I need 13.5 sq in how much should this be increased
  4. racer102

    Newbie Here

    Fire box dampers. I have a end door going in to the fire box. Where is the best placement for the damper front or side round or sliding square. should it be mounted low  middle or high
  5. racer102

    Newbie Here

    Is there any real height standards for a smoker from the ground to bottom of door is it more preference My smoker will have about 4 to 5 inches from plate to grate and leave me 10" above the grate to top will this be ok
  6. racer102

    How did you come up with your screen name?

    I use to own a Blown Alcohol Draster so I Was A Racer 102 was my car number
  7. racer102

    Newbie Here

    Here it is the start of my smoker. Thanks to Dave for the help. I'm slowly doing this as I had cancer surgery 4 weeks ago and I'm still not up to full speed so I tinker then rest for the day then work a little more Marking the cut out for the throat was a challenge but got it marked. I used my...
  8. Newbie Here

    Newbie Here

    • racer102
    • Album
    • Comments: 0
  9. 20150802_135527.jpg

    20150802_135527.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  10. 20150802_135518.jpg

    20150802_135518.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  11. 20150731_100252.jpg

    20150731_100252.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  12. 20150731_100242.jpg

    20150731_100242.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  13. 20150730_101524.jpg

    20150730_101524.jpg

    • racer102
    • Media item
    • Comments: 0
    • Album: Newbie Here
  14. racer102

    Comment by 'racer102' in media 'CC door opening height.jpg'

    That's pretty much what I had in mind 9 and 11 o'clock. I'm going to make pull out shelve or shelves not sure about 2nd shelve yet just 2 in the house now. But while I'm at it easier to add than take away
  15. racer102

    Newbie Here

    Thanks Dave greatly appreciate your advice. Now off to start up the plasma cutter and get tis thing started
  16. racer102

    Newbie Here

    So I measured the tank from seam to end of dome 43.5" so that is my true length now, not the way I was measuring it total end to end at 48". So recalc. at 43.5"
  17. racer102

    Newbie Here

    So with a dome end on a compressor tank what do I use Partial round, football ETC. ???? Also how deep do I set it into the tank
  18. racer102

    Newbie Here

    First build need advice. Will this work for a air compressor tank 20 X 48 1-   18 X 18 Fb to be used 2-  Cut into tank will be 5" from the bottom to seam which is 5" in from crown of tank 3- plate mounted flush with FB. Will be using a channel and sloping to opposite end for drain 4- cooking...
  19. racer102

    Throat cut

    new here looking for throat cut out for a 60 gal compressor tank or it's 20X48 fire box will be 18X18X18 going to cot it to the seam just need to know how  high up I need to go
View older results
Top Bottom
Back
Clicky