Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. IMG_0891.JPG

    IMG_0891.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  2. IMG_0885.JPG

    IMG_0885.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  3. IMG_0886.JPG

    IMG_0886.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  4. socalcooker

    120 gallon RF trailer build

    Cleaned up the inside of the tank under where the RF plate will be. Looked like it had dirt and at some point water that sat for quite a while. There was thick cakes on rust and clumps of dirt. I scraped it first then wire wheeled it and finished it off with a grinding wheel. I was...
  5. socalcooker

    120 gallon RF trailer build

    Cut the door yesterday and the FB to CC opening. The door sprung pretty bad, close to a 1/4" along the entire length of the bottom seam. Not sure how I'm going to approach that yet. It pulled into the tank I expected it to try and unroll. For now I'll just focus on the RF plate and grate...
  6. IMG_0877.JPG

    IMG_0877.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  7. IMG_0879.JPG

    IMG_0879.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  8. IMG_0878.JPG

    IMG_0878.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  9. IMG_0868.JPG

    IMG_0868.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  10. socalcooker

    120 gallon RF trailer build

    I got the tank and firebox welded together. The cap I welded on the end had a pretty good bow into the tank. So I had to fab a little bar that I pulled with a clamp to get it flush with the firebox. I just tacked the one end to the CC. Should have the CC door cut this week. Kyle
  11. IMG_0869.JPG

    IMG_0869.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  12. IMG_0871.JPG

    IMG_0871.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  13. IMG_0871.JPG

    IMG_0871.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  14. socalcooker

    120 gallon RF trailer build

    I've made some progress recently. The tank I planned on using was just a touch to small to get the size door I needed, so I took a longer tank of the same diameter and cut about 2 feet off of it. This got me the extra few inches I needed for a 48" door. The piece I cut off will...
  15. IMG_0827.JPG

    IMG_0827.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  16. IMG_0825.JPG

    IMG_0825.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  17. IMG_0820.JPG

    IMG_0820.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  18. IMG_0818.JPG

    IMG_0818.JPG

    • socalcooker
    • Media item
    • Comments: 0
    • Album: 120 gallon RF trailer build
  19. socalcooker

    120 Horizontal Gallon Build....First Time....Help Needed

    Also depending on location of the bungs you can use one as the drain which saves a little work. Kyle
  20. socalcooker

    120 Horizontal Gallon Build....First Time....Help Needed

    You can cut them out and patch them or plug them and put that side of tank on the bottom. On my 60 gallon I welded plugs on them and put them to the bottom. My current build I got lucky all bungs were on the domed end which I cut off. The next build I do I'll probably cut them out weld plate...
Top Bottom
Back
Clicky