Search results
-
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
-
KIMG0079.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0078.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0071.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
Need Help With A New Reverse Flow Build 275 gallon
I am doing a lower and upper intake so I can have the best control over temps and air flow. I started on a lower inlet before LenDecaturAL offered a suggestion, but my plan is similar. The dome nature of the firebox door and the 6" x 2" metal I had means the lower inlet will be angled toward...- blacked out
- Post #41
- Forum: Reverse Flow
-
Need Help With A New Reverse Flow Build 275 gallon
Unfortunately, I think side inlet sliders would be tough to get to under the frame rails and would be partially blocked by leaf spring shackles.- blacked out
- Post #38
- Forum: Reverse Flow
-
Need Help With A New Reverse Flow Build 275 gallon
The next challenge is the firebox inlets. My firebox door is curved, so I planned to take some 4" x 4" square tubing and placing it horizontally with sliding closures in a very similar fashion as most square firebox builds. However, because of the round firebox and trying to get the lower...- blacked out
- Post #36
- Forum: Reverse Flow
-
Need Help With A New Reverse Flow Build 275 gallon
The top trim is on. Despite the uneven smoker sides and top, a little extra grinding, hammering, and planning all seemed to work well as the trim looks to fit well. Due to the top's design, I was unable to trim the upper rear area near the hinges, which I anticipated. I'm still waiting...- blacked out
- Post #35
- Forum: Reverse Flow
-
KIMG0068.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0069.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
Need Help With A New Reverse Flow Build 275 gallon
Since putting the top on, there has been a large gap on the left front corner. I tried several things before, while, and after the hinges were welded on, but I was only able to lessen it and not eliminate it. It appears the top must have twisted or was used as a speed bump in front of a Jenny...- blacked out
- Post #33
- Forum: Reverse Flow
-
KIMG0065.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0064.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0062.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0059.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0058.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0056.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0057.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
Need Help With A New Reverse Flow Build 275 gallon
A little update. The water pan flange, handles, and latches are done. The front lower rack door is done with the hinges, handles, and latches all in place. I need to buy some gasket material for the doors and top. I've read some information on the forum, but almost every suggestion has been...- blacked out
- Post #31
- Forum: Reverse Flow
-
KIMG0053.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
-
KIMG0052.jpeg
- blacked out
- Media item
- Comments: 0
- Album: Need Help With A New Reverse Flow Build 275 gallon
