Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. ribwizzard

    novasbc's 250 gallon propane tank build

    I like to flip the tank over so plugs are on bottom
  2. ribwizzard

    novasbc's 250 gallon propane tank build

    Slide your plate in before welding firebox on. Here is how i recomend performing the build. 1-Fabricate firebox completely, its alot easier to get all detail work on firebox done while you can still flip it over by hand. Do not weld the two plate at the seam that will be the corner that will...
  3. ribwizzard

    Back at it.

    Now to do something about those handles, and the plugs on top
  4. ribwizzard

    Back at it.

  5. CAM00258.jpg

    CAM00258.jpg

    • ribwizzard
    • Media item
    • Comments: 0
    • Album: Back at it.
  6. ribwizzard

    Back at it.

    Started fixing some of the pos work that they had already done to the tank,,they had no seal at the top of the door. And hinges where way too small.i went old. School with the hinges.
  7. CAM00257.jpg

    CAM00257.jpg

    • ribwizzard
    • Media item
    • Comments: 0
    • Album: Back at it.
  8. ribwizzard

    Back at it.

    12218 boyette rd in Riverview. Tuesday to Sat 11 to 7.
  9. ribwizzard

    Back at it.

    I was drilling the holes in the 1/2 flat bar for the 9/16 bolts for the hinges and door latch. Thought it wasnt worrh setting up the drill press and just grabbed my 1/2 drill. Ended up wasting about 2 hours doing something that should have taken 10 minutes. And with 1/2 the bit stuck where i...
  10. ribwizzard

    Back at it.

    Still got to trim all the extra stock off and round everything out.
  11. ribwizzard

    Back at it.

    Not much done this week, just made firebox door with hinges and latch. I hate drilling holes, especicially. When you break a bit off in the hole.
  12. CAM00250.jpg

    CAM00250.jpg

    • ribwizzard
    • Media item
    • Comments: 0
    • Album: Back at it.
  13. ribwizzard

    Ash pan design help

    Stick a pie vent on the floor and attach an ash pan underneath the firebox, ( but hang it low so it gets plenty of air) then stick a nice row of vents slightly above the firegrate. For upper vent if you want one, all you need is a couple sq inches
  14. ribwizzard

    Ash pan design help

    Pie vent on bottom allows ashes to fall out. Its also better on windy days.
  15. ribwizzard

    Back at it.

    Here you can see the secondary firebox plate and why i decided to bulge out the hole cover
  16. CAM00247.jpg

    CAM00247.jpg

    • ribwizzard
    • Media item
    • Comments: 0
    • Album: Back at it.
  17. ribwizzard

    Back at it.

    Got new axle in
  18. CAM00246.jpg

    CAM00246.jpg

    • ribwizzard
    • Media item
    • Comments: 0
    • Album: Back at it.
  19. ribwizzard

    Back at it.

    I have not started building the reverse flow plate/pan yet.
  20. ribwizzard

    Back at it.

    No Dave, the hole was from the old firebox, i covered it up with the plate, the hole is still there but sealed inside the cc
Top Bottom
Back
Clicky