Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. regularjoe

    20gal build Finially DONE

    Yes everyone has been very informative on here. I couldn't have done it without all the help.
  2. regularjoe

    20gal build Finially DONE

    Picked up a set of used wheels for the smoker. Two swivel and two are stationary. ,The wheels hold air and are about 6 inches. I think they will go trough my yard pretty good. I will have a handle on the front that can also be hooked up to the tractor. Also brought home 8 pieces of 2x2x24 square...
  3. IMAG1128.jpg

    IMAG1128.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  4. regularjoe

    20gal build Finially DONE

    My neighbor took in a beef and he did not like how much fat was on the beef short ribs so he gave them to me to see if I would like to smoke them. 15lbs. I did some beef ribs before but I don't think they were short ribs. I did some reading on them in the beef section and will try them once I...
  5. IMAG1142.jpg

    IMAG1142.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  6. IMAG1158.jpg

    IMAG1158.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  7. regularjoe

    20gal build Finially DONE

    I got the hole cut out and the sides cut for the plenum. I will be using a 3in pipe and will have to try to figure out how long to make it. My plenum box will be 4.5 x 4.5 on the top and the rear is 4.5 x 4 then it will angle down to the box from there. I am guessing to start with a 24in long...
  8. regularjoe

    20gal build Finially DONE

    Got the RF plates installed. I kinda wish I would of made the sides a little bigger so it does overflow in not on even ground. I need to know how important it is to have the breather straight across the FB/CC opening? Once I put the flange on the door I lost the space that I was going to...
  9. IMAG1156.jpg

    IMAG1156.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  10. IMAG1157.jpg

    IMAG1157.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  11. regularjoe

    20gal build Finially DONE

    Drain install
  12. IMAG1154.jpg

    IMAG1154.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  13. IMAG1155.jpg

    IMAG1155.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  14. regularjoe

    20gal build Finially DONE

    Got the rear on the firebox and welded it on.  Rolled it around on the stand to weld underneath. 
  15. IMAG1153.jpg

    IMAG1153.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  16. IMAG1152.jpg

    IMAG1152.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  17. regularjoe

    20gal build Finially DONE

    Thanks. I actually have four of those ready to go if I need them. It looks like I will be taking this weekend off.
  18. regularjoe

    20gal build Finially DONE

    Got the firebox welded up. We were not able to put the back on because it was cut a half inch out of square. The cutout for the fb/cc was a nice fit too. My metal guy is going to recut it and I hope to hit it again next Saturday.
  19. IMAG1126.jpg

    IMAG1126.jpg

    • regularjoe
    • Media item
    • Comments: 0
    • Album: 20gal build. UPDATE 12/20/14 Almost done.
  20. regularjoe

    20gal build Finially DONE

    Test fit the lower cooking rack.
Top Bottom
Back
Clicky