Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  2. isaac

    Ok. Here we go again. Rf #2.

  3. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  4. isaac

    Ok. Here we go again. Rf #2.

    The rf plate is in line with the top of the FB. I capped the "gutter" for the grease where it meets the fire box. I asked about why people inset the FB, I got a couple of answers. 1. When using a pressure or prefabed tank, there is a weld seam that makes it hard to fit up, so but inserting...
  5. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  6. isaac

    Ok. Here we go again. Rf #2.

    I now have it all welded and ready to get some legs under her. I have a piece of 3.75 ss pipe 39" long that I'm going to hook up to a plenum at grate level. I'm not sure what I want to do for legs, either have the angled or straight down to a lower shelf. I want it on legs, then I'm doing the...
  7. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  8. isaac

    Plenum size/placement

    Hey there. Your cc is a 20" dia pipe? I'm in a build, my cc is 20"x40" and i was thinking about a plenum set up, what did you go with for size of pipe for cc and exhaust pipe? Any info would be appreciated.
  9. isaac

    Ok. Here we go again. Rf #2.

    Typically do people run one drain from the rf plate through the bottom of cc, this would inhibit draining of lower portion of CC? Lets say if you hosed it out or had to clean the lower portion? I was going to set the CC on a minimal slope away from the fire box, to aid in rf draining. I...
  10. isaac

    Ok. Here we go again. Rf #2.

    Too funny. I was going to pm you. My plan is to fit and weld the baffle plate in, then cap the ends and fire box weld end will be same time. One question I have is the end of the baffle plate, if my Ed height was 4.5" should I mirror that at the end? For I do it's about 70in sq Where my FB...
  11. isaac

    Ok. Here we go again. Rf #2.

    Just got it cut and sitting there for a look. Next I'm cutting FB opening. And rf plate.
  12. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  13. isaac

    Ok. Here we go again. Rf #2.

  14. image.jpeg

    image.jpeg

    • isaac
    • Media item
    • Comments: 0
    • Album: Ok. Here we go again. Rf #2.
  15. isaac

    starting my reverse flow

    Roger that Dave. My apologies for high jacking the thread.
  16. isaac

    starting my reverse flow

    Will it matter if I am rolling and installing flat ends? A true cylinder.
  17. isaac

    starting my reverse flow

    Nice work. How did you come up with the 7" to inset the fire box to the cc? i'm just in the process of my build and i see as lot of fb inserted into the cook chamber, is there any benefit to this? Or does it matter if Fb is on the outside? Im sure The Guru will have some input.........Dave? 
  18. isaac

    Ok. Here we go again. Rf #2.

    When my plates came off the burning table the cord length was 16.5" and my segment height was 4.4", i am going to use a side mounted plenum with a 4" id pipe.  Im eating a quick lunch then im off to shear my 3/16" plate for rolling. Working in a welding shop helps. once i have all the pieces my...
  19. Ok. Here we go again. Rf #2.

    Ok. Here we go again. Rf #2.

    • isaac
    • Album
    • Comments: 0
  20. isaac

    Ok. Here we go again. Rf #2.

    Just want Dave to inspect my math and confirm all is good befor I start my build. I attached a pic of my calculations for ease of not typing on the phone. Thanks all.
Top Bottom
Back
Clicky