Toggle sidebar

Search results

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. FireBox 005.JPG

    FireBox 005.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  2. FireBox 004.JPG

    FireBox 004.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  3. FireBox 002.JPG

    FireBox 002.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  4. FireBox 001.JPG

    FireBox 001.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  5. geothermal

    20" Pipe RF Smoker

    Yes, mine is 1/4".
  6. geothermal

    20" Pipe RF Smoker

    Got the plenum fabed up and welded on to the plate that connects the CC to the FB. Plate is partially welded on. I ran out of welding rods.
  7. smoker 001.JPG

    smoker 001.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  8. smoker 003.JPG

    smoker 003.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  9. smoker 002.JPG

    smoker 002.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  10. geothermal

    20" Pipe RF Smoker

    Got the RF Plate and drain welded today. Although I don't think it's necessary, I will weld on a 1" high piece on the end of the plate in case I want to fill the plate with water at times. It has a gentle 1/4" slope from the end and sides to the center drain. On to the FB!!!
  11. smoker 003.JPG

    smoker 003.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  12. geothermal

    20" Pipe RF Smoker

    Hi Dave,   I kind of wondered about that myself, but since the brake was from corner to corner both ways, all edges remained straight and square. I set it in the CC afterwards and leveled it up to cut the drain holes and it fit nice and tight against the sides of the pipe.
  13. geothermal

    20" Pipe RF Smoker

    Finished welding and grinding the end cap tonight. RF plate is next.
  14. End Cap 001.JPG

    End Cap 001.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  15. End Cap 002.JPG

    End Cap 002.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  16. geothermal

    20" Pipe RF Smoker

    Thanks again Len and Dave. Well I cheated a little yesterday and had this tank manufacturer cross bend the RF plate. Best $20 I ever spent and saved me hours of work. The plate came out perfect with about a 1/4" - 3/8" drain to the center and nice and clean looking. Started welding on the round...
  17. geothermal

    20" Pipe RF Smoker

    Question on the chimney size and length. For an RF smoker, I know your supposed to size the FB to 100%  of the CC on Feldons's calculator in order to get the opening between the FB and CC, then multiply that number by 1.5. So if I make my FB larger than 100% should I use the re-calculated size...
  18. geothermal

    20" Pipe RF Smoker

    This might be a dumb question, but do you score the top or bottom of the RF plate, or just cut it all the way through? I'm guessing the top if you score it halfway through, but then you have to grind down the welds. If you socred it on the bottom, you wouldn't have to grind them down and you...
  19. SmokerBuild 001 (2).JPG

    SmokerBuild 001 (2).JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
  20. Slinger Speedway 004.JPG

    Slinger Speedway 004.JPG

    • geothermal
    • Media item
    • Comments: 0
    • Album: 20" Pipe RF Smoker
Great deal on LEM Grinders!
Top Bottom
Back
Clicky