Toggle sidebar

Recent content by snaggletoe

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. snaggletoe

    Initial Setup and Using the Masterbuilt Vertical Propane Smoker

    Smoker21 - My unit did not come with sht wheels. It came with NO wheels. Check out post #186. I built a small dolly of scrap rough cut 1inch wood I had laying around and then attached it to the bottom of the stock legs. Then installed 3inch diameter industrial casters on a 3/8 threaded stud into...
  2. snaggletoe

    Initial Setup and Using the Masterbuilt Vertical Propane Smoker

    jimmy1957 You probably wouldn't need the lid. I think, in some perverse way it helps to reduce flare ups, keeps juices off the wood, helps moderate temp, or just IS because that's how it was given to me - which all contribute to my enjoyment of smoking. If I ever have to replace it,  I will...
  3. Bacon sliced 2.jpg

    Bacon sliced 2.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  4. Bacon sliced 2.jpg

    Bacon sliced 2.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  5. Summer Sausage.jpg

    Summer Sausage.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  6. Slabs in smoker.jpg

    Slabs in smoker.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  7. snaggletoe

    Initial Setup and Using the Masterbuilt Vertical Propane Smoker

    Cast Iron Chip Pan. This one was given to me. I have no idea what brand or where it even came from??  Works great though. The bolts are drilled and tapped for any needed height adjustments. These photos where taken when the smoker was brand new.
  8. IMG_20140528_200558_016.jpg

    IMG_20140528_200558_016.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  9. IMG_20140528_200611_310.jpg

    IMG_20140528_200611_310.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  10. IMG_20140528_200618_127.jpg

    IMG_20140528_200618_127.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  11. snaggletoe

    Initial Setup and Using the Masterbuilt Vertical Propane Smoker

    Mine is two yrs old. I never needed the needle valve mod or the door gasket mod. Mine can be set as low as 100 degrees F and is very stable with the stock controls. The door seals just fine. I got rid of the stock chip pan. I never used it once. Anyone want to trade for a AMNPS product?  I have...
  12. Initial Setup and Using the Masterbuilt Vertical Propane Smoker

    Initial Setup and Using the Masterbuilt Vertical Propane Smoker

  13. Smoker back.jpg

    Smoker back.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  14. Smoker front.jpg

    Smoker front.jpg

    • snaggletoe
    • Media item
    • Comments: 0
    • Album: Initial Setup and Using the Masterbuilt Vertical Propane Smoker
  15. snaggletoe

    Masterbuild XL Mods - Post your mods here!

    This is the one I have. http://www.midwayusa.com/product/777254/masterbuilt-sportsman-elite-gs30d-2-door-propane-smoker
See more
Top Bottom
Back
Clicky