Follow along with the video below to see how to install our site as a web app on your home screen.
Note: This feature currently requires accessing the site using the built-in Safari browser.
Recent content by pbft
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
It's quite a bit heavier - the propane tank adds a lot. It's OK on smooth surfaces, but it's definitely heavier to lift. The sear box flexes a bit when you lift it up to roll around.
I added big pneumatic tires to replace the originals, and I added casters on the right end. With that it's a...
That makes sense. The Trailblazer doesn't have a smokestack on the end. I like the proximity of the grill and the gas jugs - life should have the possibility of excitement ;-)
Looks like you mounted yours much farther forward. Did you do that to leave the Rec Tec grease drain accessible? I set mine up so the Rec Tec drains into the Camp Chef drip tray.
I did a write-up in an older thread here:
https://www.smokingmeatforums.com/threads/rec-tec-camp-chef-sear-box-add-on.284211/
Short story:
I made a cardboard template of the end of the RT340 and used that to locate the hole that I had to make in the sear box for the grease drain.
I lined up...
I've posted a couple of intermediate progress reports, but it's finally pretty much where I want it. Smoking chicken parts tonight to celebrate.
Mods:
Camp Chef sear box
Bottom shelf
Folding front work surface
Gaskets for top and bottom edge of door
Insulating cover (made from carbon fiber...
I'm using the Inkbird 4 probe unit. I paid $50 during an Amazon special. It seems to have a really good range, but it doesn't allow viewing from your phone - only from its receiver. Temperature readings seem very accurate, and you can set individual alarms to pull of different cuts when they're...
Thanks. I feel like the Trailblazer is a great smoker / grill. These mods were pretty easy and make it perfect for my needs. Just did three pork butts yesterday, and will do a whole batch of chicken parts tomorrow. The front work shelf is really nice, and much more useful than the side work...
I've been working away on mods to my RT340 Trailblazer. It has replaced my old Genesis and Masterbuilt bullet smoker. I loved it 'out-of-the-box', but I'm never happy until I've figured out a few improvements. Here's the list of mods to date:
Camp Chef sear box. I wanted to be able to do a...
It gets cold here in the north, so I took a scarp of 1/4" carbon fiber welding blanket and made a 'cozy' for the Trailblazer. The welding blanket is a little like soft felt, so I stitched a scrap of quilting fabric to the top surface. I used 10 lb test spectra fishing braid, which is good for...
Measurements are approximate - best I could do without unmounting it: The hole is 1 1/4" wide by 2" high. The front edge is 6 1/2" from the front of the sear box panel, and the top is 3" below the top edge of the sear box panel.
PM me if you have specific questions. The sear box is a bit flimsy compared to the RT-340 but I'm pretty happy with how it turned out. There are few things on Amazon with reviews as uniformly positive as the sear box. I think it's a great addition. I'll be searing sous vide steaks on it tonight...
I liked the Woodwind and that was going to be my choice. I especially liked the sear box option. I do a lot of sous vide where I need a fast sear, and sometimes I just want to do a quick grill of something small.
Last month Rec Tec has the RT340 for $600 delivered. It's a much more solid unit...
So - my Trailblazer will overshoot if it's making a big change, like from 40 to 450 all at once. If it overshoots by enough it will do the fan and auger cycling thing. I haven't run it with a large load yet, but I can imagine that it might make that behavior more likely.
It's a characteristic...