Toggle sidebar

Recent content by mooch91

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. mooch91

    Back panel of MES30

    Has anyone experienced the back panel warping on their MES30? If so, what did you do about it? I had mine off for component replacement and now is the time to straighten it out before screwing it down. Thanks!
  2. mooch91

    MES30 GFCI trip

    Thanks @tallbm , I will probably just over-ride the switch if I need to do a smoke before the new one arrives. I just wanted to get this thing buttoned back up, it's been all over my basement for a couple of weeks now. In terms of the new stake-on connectors - is it advised to heat shrink...
  3. mooch91

    MES30 GFCI trip

    Ahh rats. The ones I received today are the two-piece design. I will take a look at the ones you sent the link for. Though I don't think they will be received until next Wednesday. Maybe I'll contemplate cleaning up the connectors on the existing one and putting it back in temporarily (it...
  4. mooch91

    MES30 GFCI trip

    Thanks. I ordered the cutout switch (pack of 5) and the high temp stake-on quick disconnects from Amazon. Should be here Monday.
  5. mooch91

    MES30 GFCI trip

    I took the back panel off, and it looks like the high temp cutout is the issue. The box surrounding the switch had some rusty corrosion on it, and when I took it off, one of the terminals was barely left, both had a lot of corrosion. I also found that the ground for the heating element was...
  6. mooch91

    MES30 GFCI trip

    Will probably try that tonight or tomorrow to confirm. I have only tried a couple of outlets on the same GFI circuit.
  7. mooch91

    MES30 GFCI trip

    All, I've read most of the posts about MES30 smokers tripping GFCIs. I have a unit that is now about 6 years old. After only 5 years and about 20 smokes, it started tripping the GFCI outlet where I plug it in, mid smoke. I set it aside and am now getting back to it. Most of the issues seem...
  8. mooch91

    Electric smoker on screened vinyl deck?

    Thanks Red Dog. I did smoke today, brought it down to the paver landing so I could get a feel for it.  I'm going to bring it back up and situate it next to the propane grill (outside, to the right in the photo) for the next smoke.  I think I could do it under the covered portion of the deck if...
  9. mooch91

    Electric smoker on screened vinyl deck?

    I think I was less concerned about heat and more concerned about the potential for fire.  I did season it on the deck and saw no issues with heat, but I guess I'm concerned having heard of some of the MES units spontaneously combusting.  I think for my first smoke I'm going to do it down on the...
  10. Electric smoker on screened vinyl deck?

    Electric smoker on screened vinyl deck?

    • mooch91
    • Album
    • Comments: 0
  11. mooch91

    Electric smoker on screened vinyl deck?

  12. IMG_20141225_112220_zpsb3c93e16.jpg

    IMG_20141225_112220_zpsb3c93e16.jpg

    • mooch91
    • Media item
    • Comments: 0
    • Album: Electric smoker on screened vinyl deck?
  13. mooch91

    Electric smoker on screened vinyl deck?

    All, Wanted to get out and do my first smoke today.  But it's drizzling/raining here in eastern PA.. Reading the instructions on my MES30, it says it should not be used in the rain, for obvious reasons I suppose. Would you feel comfortable operating your smoker on a screened vinyl deck? I'll...
  14. mooch91

    MES 30 chip tray position

    The tray itself should sit above/on the heating element, no?
  15. MES 30 chip tray position

    MES 30 chip tray position

    • mooch91
    • Album
    • Comments: 0
See more
Top Bottom
Back
Clicky