Recent content by clearprop

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. clearprop

    First smoker build question

    Will an oven element fit inside the diameter of the tank? depending on the shape of the element, you could probably drill some hole for the leads to come out and a wire bracket to support it on the inside -OR- You can buy unbent straight but bendable elements in the "green" form where the...
  2. clearprop

    Hot Cart Build

    Where is the air intake? The stack could be drawing more draft and bringing in cooler air too fast. How many cubic feet is your unit? 1200w for that large of a space (judging by your picture) isn't enough from what I've seen. It will be way easier to get it up to temp if you had more wattage...
  3. RTD PT100 probes for Auber PID's

    RTD PT100 probes for Auber PID's

  4. clearprop

    RTD PT100 probes for Auber PID's

    I'm glad you said that.... I just found this on Auber's website when researching what you said: "This Air intake sensor features high accuracy and fast response time in the air because of its thin RT­D sensor tip."...
  5. Air Instak.jpg

    Air Instak.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: RTD PT100 probes for Auber PID's
  6. PID Thermal limit (1).jpg

    PID Thermal limit (1).jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: PID problems runaway temp
  7. PID Thermal limit (1).jpg

    PID Thermal limit (1).jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: PID problems runaway temp
  8. clearprop

    RTD PT100 probes for Auber PID's

    I talked with Auber. A  longer 5" probe that's a skinny 1/8" diameter is good for air temp. If you want use a thicker one, make sure it is shorter. It takes air longer to change the temperature on a sensor with more mass/metal if that makes sense.
  9. clearprop

    Intake and exhaust sizes on electric smokers

    Ended up doing a combination of everything. 3"OD 14ga aluminized exhaust pipe. It has a long swooping curve, the bottom 1" has no bend/elbow. It has a slight lip near the opening, and angles back slightly so any built up creosote condensation should not drip onto the food. I driled my rear hole...
  10. 20170327_211059.jpg

    20170327_211059.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
  11. 20170327_211038.jpg

    20170327_211038.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
  12. 20170327_210600.jpg

    20170327_210600.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
  13. 20170327_210550.jpg

    20170327_210550.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
  14. 20170327_201731.jpg

    20170327_201731.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
  15. 20170327_194151.jpg

    20170327_194151.jpg

    • clearprop
    • Media item
    • Comments: 0
    • Album: Intake and exhaust sizes on electric smokers
See more
Top Bottom
Back
Clicky