Dutch Oven Table

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

wolfmann

Smoke Blower
Original poster
Apr 3, 2011
82
12
Richmond Texas
I was ask if I could build a Dutch Oven Table. Well thanks to the Internet I was able to figure out what that was. LOL Here are a couple of pictures what i came up with. He also wanted to be able to move it easier. So I build it so it sits on the frame and can be taken off by just lifting it of so it will be easier to move in the truck.

I will take a picture of the finished paint job today it was a little to dark when I was done.

http://i291.photobucket.com/albums/ll319/Domberg/Dutch Oven Table/Dutchtable002.jpg  

http://i291.photobucket.com/albums/ll319/Domberg/Dutch Oven Table/Dutchtable004.jpg  

http://i291.photobucket.com/albums/ll319/Domberg/Dutch Oven Table/Dutchtable005.jpg  

http://i291.photobucket.com/albums/ll319/Domberg/Dutch Oven Table/Dutchtable006.jpg  

http://i291.photobucket.com/albums/ll319/Domberg/Dutch Oven Table/Dutchtable007.jpg  
 
  • Like
Reactions: rabbithutch
Wolfman,that's a fine looking job there,unless there will be a lot of heat loss from under the table where all the open space is,it should do DO cooking well.

I'd like to see that in use.

Thanks for the look and
 
I also would like to know how well it turned out in cooking. It's all good my friend.
 
I was ask if I could build a Dutch Oven Table. Well thanks to the Internet I was able to figure out what that was. LOL Here are a couple of pictures what i came up with. He also wanted to be able to move it easier. So I build it so it sits on the frame and can be taken off by just lifting it of so it will be easier to move in the truck.

I will take a picture of the finished paint job today it was a little to dark when I was done.


40793f05_Dutchtable002.jpg


26c3591e_Dutchtable004.jpg


ae284b1e_Dutchtable005.jpg


c206774b_Dutchtable006.jpg


7dd7487b_Dutchtable007.jpg
Nice work
 
 
I will let you know how it works once the young man that ordered it fires it up. As for the heat loss oldschoolbbq the cast iron pots will be sitting in the coal so it should work fine.
 
You do both you make a deep be of charcoal and the once the pot is set in you cover the lid with charcoal too. So you will be getting heat from top and bottom crating more the effect like an oven.
 
You do both you make a deep be of charcoal and the once the pot is set in you cover the lid with charcoal too. So you will be getting heat from top and bottom crating more the effect like an oven.


I tried my luck a few times at dutch oven cooking, it's pretty cool.

Picked up a Huge Lodge Dutch Oven and made stew, dropped some bisquick biscuits in there popped on the lid and put a few coals on top and the biscuits browned, pretty cool.

I cant find a pic with the top browned but here's one with the biscuits before they were browned

c9d0f223_2198416960041211880S600x600Q85.jpg
 
  • Like
Reactions: rabbithutch
well ECT01 what size do you need. I am always looking for the next build. I am starting a 2 burner cooker with a prep area for the same guy.
 
Wolfman you are obviously very talented. I think you could easily sell this stuff, and start a part time business, or maybe full time! 
 
Thanks Al

I do sell smokers and anything anybody wants build on a part time base right now. I would like to retire from my job and get in to building full time in the next 2 years. The other avenue i want to explore more is rebuilding and repair. I found there is not a lot of that available.
 
Nice table..hubby is building mine now and will post pics when done..the table is half inch aluminum plate and its all found materials, but will be nice too.
 
I am looking forward to see the pictures. I am still in the possession of the table. The guy that I build it for was coming down to Houston but some how that did not happen. We are now trying some how to get it to him but I might end up selling it local.
 
Ah thats too bad.. If you have to sell it, see if there is a local online D.O. society in your area and maybe you can offer it there.. The only ones out there on the market are Made in China, and these people know a nice table when they see one..good luck
 
Thanks I did not know was a D.O. society. I will look that up. I did see some of the ones that are for sale but you are right there not even close to this one. That is how I actually figured out how to build this one.
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky