Recent content by killerb468

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
  1. killerb468

    Compressor tank to a backyard smoker

    I will be on it around Thanksgiving. I will start a new build thread.
  2. killerb468

    Compressor tank to a backyard smoker

    I will be starting it around end of july.
  3. killerb468

    Compressor tank to a backyard smoker

  4. killerb468

    Compressor tank to a backyard smoker

    I mentioned above I needed to keep the stack short due to enclosed trailer. This easy on and off extension does not leak. So I won’t weld the collar to the extension. Easy to remove and stire.
  5. killerb468

    Compressor tank to a backyard smoker

  6. killerb468

    Compressor tank to a backyard smoker

    I did cut the old stack out and put a 4 1/2” diameter stack. Had to keep the stack short to get it into my enclosed trailer. I made a 15” extension so it is 36” above cc. Here is a ouc without extension. Did a run last week and the week before. Door is all sealed and can go from 150° to 400°...
  7. killerb468

    Compressor tank to a backyard smoker

    Been almost 10 years i have made a few changes and today i changed out the smoke stack. Long story short I have dealt with a leaky (not bad) cc door. So a few weeks back decided to seal it off. And low and behold I could not get the CC above 165°. Cut and scraped the seal off as I was at a...
  8. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Digging this build, here is Frankenstein… I have cut i to it several times since building it 8 years or so ago. Getting ready to out a new stack on it. Glad I didn’t paint it. I like the rusty look.
  9. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Look forward to seeing the progress
  10. killerb468

    Burger Brawl Voting Poll....Some Amazing Entries!! (Pretty Long)

    Great batch of entries right there.
  11. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Yea I meant FB, are you going to make it 1 rack or 2?
  12. killerb468

    Red's 24x46 Reverse Flow Patio Build

    Nice build you have going. I built one years back. I am about to start another build. What size DB did you go with? I am going to run a 24” x 24” FB on my 24”x 46” tank. Keep up the solid work.
  13. killerb468

    Tine to build another smoker

    So I an passing on the tank. Should I look for another one or just raise the roof and have a split door on my old smoker. Cut and raise 4 or 6”. I believe I have seen it done on here. Could find the thread.
  14. killerb468

    Tine to build another smoker

    I haven’t seen it yet to lnow if it is galvanized or not. How would you know if if is glass lined? Also is there a scratch test gor galvanized propane tanks? Might be better to mod my existing smoker and add 6” to it for another rack. Here is the freak, built 10 years ago. Still doing work.
  15. killerb468

    Tine to build another smoker

    I was given this tank and before I put time into it. Will the center weld seem be an issue other than cosmetic? Don’t want it to do funky stuff when I cut it open. Measures to be a 125 gallon and want to make a horizontal RF out of it. Please, any thoughts would be appreciated.
See more
Top Bottom
Back
Clicky