1. Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.

How to season or cure your masterbuilt electric smoker.

By texacajun, Dec 3, 2012 | | |
  1. Seasoning/Curing your smoker

    All new smokers need to be "cured, seasoned or preseason” to ensure the removal or machine oils, dust, and other materials left over from the manufacturing process. This also helps in rust prevention. During manufacture, there are all sorts of petroleum oils and contaminants used that you really do not want to have in the smoker while cooking. Also this will remove any solvents that may be left in the paints used on your smoker.

    1. Clean the inside of the smoker. Use a mild soap detergent and water to wipe down the inside. To

         include the grates or racks, sides, top, bottom, grease tray. Then rinse everything down with

         water.  Allow it to air dry. You can leave the smoker open or wipe off any excess water.

    2. Once it is dry, spray the insides with a spray can of cooking oil like Pam or you can wipe it down

        with cooking oil. Make sure that everything is coated but not oversaturated with oil dripping off. The

        chip tray, heating element, grease tray, and water tray do not need to be coated with oil.

    3. Next you will need to heat the smoker up to simulate smoking.  Place the water pan in the smoker

        but do not add any water to it. Open the top vent all the way. Set the temperature to the max

        setting (for most Masterbuilt electric smokers this is 275 degrees F) Set the time for 3 hours.

    4. Adding wood chips. I use this method  taken from Deltadude  “For the MES start out with 8-12

        chips only, about 20 minutes later add another batch of chips same quantity, after the 3rd batch

        you can increase the quantity a little because you have a hot bed of ash, but be careful too much

        chips and you get black smoke.  Black smoke is creosote, which imparts a real bitter taste to your

        meat, which is nothing but bad. 

        When you first put chips in you will get white smoke, you will get white smoke with both dry or wet

        chips.  Since you are putting in so little amount of chips if they are soaked the amount of white

        smoke will be the same, there is not enough moisture to create steam.  Yeah you can hear the

        chips sizzle when you put them into the tray that is the exterior moisture of loose water, since you

        most likely will take the chips right out of whatever you are soaking them in.  Since you can't use a

        lot of chips in the MES that is why I soak mine to get a few extra minutes of burn/smoke time. 

       The white smoke will settle down into TBS (thin blue smoke) this is what you desire, TBS will not

       smell bitter coming out of the vent (BTW keep your vent wide open in the MES if using wood

       chips.  TBS actually has a sweet smell, and that is what is kissing your meat adding flavor.

       Remember, after the 3rd dump of chips there is hot ash inside and even though the visible smoke

       will dissipate your meat is still getting smoke, just smell at the vent that is one way to tell.”

    5. After the 3 hours are done you will need to let the smoker cool down. Then you can empty your

        wood chip tray of any ashes or unburnt wood chips. You will never need to scrub the inside of

        the smoker clean again. Leave it coated with the smoke residue. You can wipe it down

        occasionally to get the loose stuff off. If you need to clean the racks you can place them in the

        dishwasher. If you have a window on your smoker here are some cleaning tips for that from



       1. Cleaning it while it is still warm works best.                                                                                       


       2. No chemicals are used at all. Use some wet paper towels and the left over ash from your

           woodchip tray. What you want to do is get about 6 paper towels. Take two of them, and ball them

           up & run water on them to get them a little less than dripping wet. Then open your woodchip tray,

           and dab one side of those two balled wet towels into the ashes. Also individually ball 3 other

           paper towels, and get them less than dripping wet. Keep the other paper towel dry.


       3. All you do is put the wet paper towels with the ashes on, against the glass & scrub it just like you

           would scrub any window, until the whole thing is smeared up.

       4. Then using the other wet paper towels one at a time, keep wiping the glass. It will get cleaner

            with each wet paper towel. How many wet paper towels it takes will depend on how dirty it was to

            begin with.

       5. Then when it looks clean enough to you, buff it with the dry paper towel-----Done!

    Thanks to Deltadude and Bearcaver for their input on this.

    Share This Article


To make a comment simply sign up and become a member!
  1. FBX
    Picking up a masterbuilt 30" electric smoker today after work. I will probably cure it tomorrow after work. Thanks for the how to. Can't wait!
  2. smokeshowingbbq
    Read tonight to use 50/50 mix of water and apple cider vinegar to clean the inside of the MES. 
  3. murfman6
    Thanks, I just got my MES yesterday and will use this to season it this weekend
  4. bh smokin que
    Super information for me since I have new MES. Thanks D & B
  5. paul catt
    Thanks I was worried about cleaning the window will give the ash a shot
  6. billybob03
    Cool, thanks!
      molar likes this.