Rollin with Bling Bling Now

solar · Aug 22, 2008

Last week I put my SnP up on blocks and removed those tiny little round plastic disks Brinkmann calls wheels. My Sawzall make quick work of these pieces of crap.

And replaced them with some sweet mower wheels with a solid axle, yeah that's right, I'm rollin' cool now.

pineywoods · Aug 22, 2008

Looks good but wheres the spinners

fatback joe · Aug 22, 2008

You need some spinners. LOL

Nice upgrade

solar · Aug 22, 2008

Hey, at least the axle and nylon locking nuts are chrome, sort of. LOL

pineywoods · Aug 22, 2008

It is a great mod and should make it roll much better!!

sbv32 · Aug 22, 2008

Awesome, now I know what I an do with the old mower that I need to get rid of. Take the wheels and get rid of the rest.

solar · Aug 22, 2008

Oh yeah, it's a great upgrade, before I couldn't put it in my shop behind the house because the "wheels" would get caught on the stepping stones.

There you go!! It's basically what I did, but my neighbor gave them to me off his old mower. I think he got tired of the spicy language he would hear when I tried to move it into my shop.

1894 · Aug 22, 2008

Forget the spinners

, You may be able to find some chrome hub caps though

, And a chrome stack that you can adjust for the current wind direction

.
Thinking about one of those for my chargriller , dang wind comes from opposite directions over the course of a cook. I get dizzy spinning my smoker around

cman95 · Aug 22, 2008

Nice man....can ya smoke them thar wheels??

daboys · Aug 22, 2008

Hey thanks solar. My mower shelled out last weekend. Looks like the SnP is gettin some new shoes.

solar · Aug 23, 2008

It's a really easy mod, I used a 24" long 5/8 threaded rod with some locking nuts and washers. The most expensive thing to buy was the 5/8 drill bit.

t-bone tim · Aug 23, 2008

Does them thar wheels make that thang smoke faster

...JK , I love add on's , nice job

smokin365 · Aug 23, 2008

HMMMM......i got an old dixon in the shed, i could have a ZTR Chargriller!!

pops6927 · Aug 23, 2008

Take a little length (4" or so) of threaded pipe that is an OD smaller than the ID of the front legs and put pipe caps on them, slide 'em up inside the front legs and drill a cross bolt to hold 'em and you should have just about the right height extensions for the front legs to make up for the taller "wide ovals" on the rear. Throw a 3-speed Hurst stick on it and take it for a lap!

solar · Aug 23, 2008

Good idea, but that sounds like to much work, the 2x4 works just fine.

I do have a brand new Mallory ingintion system sitting in my closet from my old 442 I could add to it though for faster starts.

vince · Aug 23, 2008

Good Idea, Iwas thinking about that for my SNP, I hae a few junk mowers

morkdach · Aug 23, 2008

like what ya did i took a piece of 1/2" id. x 5/8" od. tubing and did the same befor i ever rolled it out the door.

skidder · Aug 23, 2008

I did the same mod to my Bar-b-chef.

cowgirl · Aug 23, 2008

Nice setta wheels!

Rollin with Bling Bling Now

Smoking Fanatic

SMF Hall of Fame Pitmaster

Master of the Pit

Smoking Fanatic

SMF Hall of Fame Pitmaster

Fire Starter

Smoking Fanatic

Smoking Fanatic

Master of the Pit

Smoking Fanatic

Smoking Fanatic

Master of the Pit

Smoking Fanatic

Gone but not forgotten. RIP

Smoking Fanatic

StickBurners

Master of the Pit

Newbie

Legendary Pitmaster

Similar threads

Hot Threads