› Forums › Smoking Supplies & Equipment › Electric Smokers › Smoke..then no smoke.....
New Posts  All Forums:Forum Nav:

Smoke..then no smoke.....

post #1 of 14
Thread Starter 
I smoked some turkey Thighs yesterday...and didnt have a problem with getting real thin bluie did the same thing...and I can't get ANY Smoke...all I see is the heat vapors coming from the vent...I am doing a ham today...and its been on there for over 1.5 hrs...and no smoke....can anyone give me a reason for this?

post #2 of 14
Did you forget the wood chunks? Or maybe your wood has been seasoned too long.

If it's seasoned wood, it's best t soak the wood chips for the smoke.
Good dry seasoned wood doesn't exactly give off a whole lot of smoke.
post #3 of 14
i won't go into the debate on soaking the chips........but you soak em......they just sit and steam till dried out......then smolder.........

if you can SMELL are fine........sometimes you won't get TBS.......if you can smell wood are fine
post #4 of 14
Did your wood catch on fire?
post #5 of 14
Thread Starter 
Well Yesterday...I used the same chips..( hickory) same amount...and I saw smoke..NOt soaked. I didnt see ALOT of smoke..but there was steady in..I saw smoke most of the time..but it was everyone talks about.

Today...I went to put the same amount of the little alumi bowl shape thing I made...and the chips that were in there from yesterday...were still there...just a darker color..but non of them had appeared to burn to ash.
I just added some extra on top of them...and like I said today i don't see ANY smoke...NOt even a hint of smoke. I know if you can smell it its doing iyts one would think it being a would see a little smoke now and again.
post #6 of 14
Hit them with a torch.........that will get them going. PDT_Armataz_01_18.gif
post #7 of 14
you shoulda emptied the container......then add new.......give that a shot
post #8 of 14
Maybe you insulated them from the bottom of your chip holder. Doesn't sound like it is getting real hot if they didn't ash yesterday.PDT_Armataz_01_05.gif
post #9 of 14
Thread Starter 
I just checked them...and when I lifted the upper section of the smoker get to the chips...I did notice they were starting to smoke...but I have no clue where its going..cause it sure isnt coming out of the smoker anywhere...oh well...Screw I just won't worry about it.

Thanks for your advice...this si my first attemp with the MES...I have a Propain version at home...and never really have alot of problems getting it to smoke..this whole elecric thing is new
post #10 of 14
What is the weather like today as opposed to yesterday? The smoke is probably there.. but if there is even a slight steady breeze, the smoke may be dissipating before you can see it.
post #11 of 14
Thread Starter 
Its 70 and very lite breeze...I would have to say it was more of a breeze yesterday...confused.gif
post #12 of 14
Like Magnum said, dump out the old and start with new on the bottom.
post #13 of 14
Why did you make a little alumi bowl shape thing for chips? The MES already has a chip holder that slides out to empty the ash and gets loaded from the side by a cylinder type loader.
post #14 of 14
Try putting chips in the chip holder. That will help a lot. It will be closer to the elect. element than setting on top of it in a bowl. Get rid of the old chips, they are charcoal now and will not smoke much the second time. They will provide insulation for the new chips.
That tray in the MES your talking about might be the water pan. Just a thought.
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Electric Smokers › Forums › Smoking Supplies & Equipment › Electric Smokers › Smoke..then no smoke.....