or Connect
SmokingMeatForums.com › Forums › Smoking Supplies & Equipment › Wood Smokers › Building a offset smoker....upated
New Posts  All Forums:Forum Nav:

Building a offset smoker....upated

post #1 of 14
Thread Starter 
For those of you that want to see this from the beginning can see it here..http://www.smokingmeatforums.com/for...ead.php?t=4437
Finally got the axle and rubber tires mounted
Also installed some aluminum strips at the sides of the door to seal it up better!
I removed the side table on the right and am gonna put some kind of handles so i can roll it around with ease! All i really have left to do is extend the legs, mount the exhaust stack (4" black pipe) and seal up a few more holes, and then some clean up and a fresh coat of heat paint!
She's so close, looking very forward to firing her up, maybe be a good reason to get the Michigan SMF together for some Q!!cool.gif
post #2 of 14
looks good. i am almost done with my newest creation. i haven't had much time to work on it lately.
post #3 of 14
hot dang that a good looking rig.....need to get my welding jucies going.. and built me one...
post #4 of 14
Almost there Bubba - and doing a mighty fine job!
post #5 of 14
Lookin good there Bubba. Can't wait to see it when you get it done. I've been finding myself looking longingly at offset wood burners. Me thinks there may have to be one in my future. I'm trying to hold off until next year because I'm looking to relocate out of state and want to keep the toys I have to move to a minimum.
post #6 of 14
Looks good cuz PDT_Armataz_01_37.gif Hope im over for the first smoke!!! DB BBQ
post #7 of 14
Looks good Bubba! That is a prime candidate for pimpin'! PDT_Armataz_01_34.gif
post #8 of 14
looks like some good progress there Steve..... the hardest parts are done now

i think its time to have a SMF Michigan Chapter "meating" soonPDT_Armataz_01_25.gif
post #9 of 14
Thread Starter 
Well, she's almost done! Got the vent installed

The SFB is sealed up, used fireplace gasket material and chimney sealer

Got some of it cleaned and painted

gotta seal up a couple more holes and hopefully get to fire it up later today, keep ya postedicon_cool.gif
post #10 of 14
Lookin good there Bubba PDT_Armataz_01_34.gif , now let's bring on the meat PDT_Armataz_01_29.gif
post #11 of 14
looks very nice. i can't wait to finish my newest one.
post #12 of 14
built well looks greatPDT_Armataz_01_37.gif

I' all for Michigan SMF getting together for some QPDT_Armataz_01_40.gif
post #13 of 14
Hey Bubba... I'd like to be in on a get together iffin' any's in the works for the Michiganian Chapter.
post #14 of 14

Bubba, Tonto, Bud (smokin' scotsmen), are in Silver Lake championship comp today crew dawg is there judging. I will be there & a few others check out http://www.smokingmeatforums.com/for...ead.php?t=8137 or http://www.smokingmeatforums.com/for...ead.php?t=6634
Yesterday I did get to meet bubba, bud, tonto, & crewdawg & they told me to tell everyone HELLO from Silver Lake.

I know it is across the state but if you, or anyone else can make it today it would be coolPDT_Armataz_01_42.gif

Hope to see more than just those listed in rollcall for Silver LakePDT_Armataz_01_34.gif
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Wood Smokers
SmokingMeatForums.com › Forums › Smoking Supplies & Equipment › Wood Smokers › Building a offset smoker....upated