Single Chamber Smokehouse

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

csgreenknight

Newbie
Original poster
Dec 7, 2016
1
10
First post here. Hopefully you all can help.

One of the selling points when I bought my house was the built-in smokehouse in the backyard. I'll try to post a pic later.

Its about 3'x3' and about 4' high. There is a smoke stack in the roof. There is an air vent low on the side that I send my probe thermometer cables through, but I leave it closed. Inside there are 3 shelves. Top 2 are where I put my meat. the bottom one is where I place a pan of water.

After I moved in and went to try it out, I found the flaws. This is a single chamber smokehouse. There is no fire box. What the guy did, and what I am doing, is in the bottom of the house I have a propane heater. On top of the heater I have a 17" cast iron skillet. this is where I put my wood chips. I have tried chips and chunks. It is impossible to control the temperature! I go along okay at 210 - 230....but then I get a flair up. I open the door to see my chips/chunks on fire! I started keeping a squirt bottle near by to put out the flames.

Any ideas you guys have? I hate opening the door every 10 minutes just to make sure my wood isn't on fire, losing that great smoke and heat.

Thanks.


 
Last edited:
Hello and welcome to you.

I'm glad you're here.

You need to get you an Amazen  AMNPS.

Try this link, that will fix your chip flare ups.
I've got one and it works great.

Then you just adjust your heat to what you want.

Independent of your smoke.

Hope this helps you out some, try it, if you're still

having a problem. 

Just ask, you will receive answers.

Have fun.

  Ed
 
How high is the skillet above the flame ?? Could be the pan needs to be a little higher off the flame ...

Also... how are you controlling the flame ?? Do you have a needle valve in-line for control ??

Also... do you have any kind of cover over top of the skillet ?? keeping fat drippings from landing in it and helping cause the flare up ??
 
Last edited:
I would also suggest you think about switching from gas to electric... Although not as bad when HOT smoking (225`+)... When I smoked some snack sticks and sausage in my smokehouse (at low temps of 120` - 170`) .. the flame had to be so low that it blew out a few times... If it weren't for my remote thermometers I would have never knew the flame went out until I went out to check on it (which could be hours at a time) .. So I just pretty much created a bomb that only needed a spark to ignite... For this reason I switched to electric ... But as I say... not as likely to happen when hot smoking (big flames) ...
 
wrap the wood in a double layer of foil    punch holes in foil    throw in fry pan    punch more or less holes till it smolders as desired      

Red
 
 
Hello and welcome to you.

I'm glad you're here.

You need to get you an Amazen  AMNPS.

Try this link, that will fix your chip flare ups.
I've got one and it works great.

Then you just adjust your heat to what you want.

Independent of your smoke.

Hope this helps you out some, try it, if you're still

having a problem. 

Just ask, you will receive answers.

Have fun.

  Ed
I agree with Ed.

I would go with an Amazing Smoker.

However I would go with the Tube type unit--AMNTS, since you're cooking with Gas.

Just go to the web site Ed posted above & look for "Tube" smokers.

That way your Gas Smoker will handle the heat, and your Tube will handle the Smoke, and neither one will affect the other.

Bear
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Clicky