or Connect
SmokingMeatForums.com › Forums › Smoking Supplies & Equipment › Charcoal Smokers › Calling all OKJ Longhorn owners!
New Posts  All Forums:Forum Nav:

Calling all OKJ Longhorn owners!

post #1 of 13
Thread Starter 

Ok so I'm looking at creating my own baffle/tuner for my Longhorn smoker instead of buying one.

 

Is anyone who has their own willing to give measurements and size of holes and distance between holes to help me out.  Also what size thickness metal did you go with?

 

Hoping to find info one setups people have found to work the best.

 

I have tried searching and have found nothing that helps me.  So either there is little out there or I'm not very good a searching.

 

Thanks in advance.

post #2 of 13
Thread Starter 

No one has any info?

post #3 of 13
This link should give you dimensions

http://www.horizonbbqsmokers.com/accessories-1/20-convection-plate

I don't own a OJL so I can't get you measurements.
post #4 of 13
Thread Starter 

Thanks,  I've seen that but the big thing is what size holes and spacing have people found to be best.

post #5 of 13
Quote:
Originally Posted by Hawks05 View Post

Thanks,  I've seen that but the big thing is what size holes and spacing have people found to be best.

I don't think it matters all that much. 8 holes for width and it has 8 holes for length.

I had one that didn't have any holes only slightly shorter in length. And it worked.
Some people like to use tunning plates.


http://www.smokingmeatforums.com/newsearch?search=Convection+plate+OJK
Check this out.
post #6 of 13
Thread Starter 

Another question I have is what did you use to clean/scrub the CC door before applying the Fireblack125 gasket?

post #7 of 13
Quote:
Originally Posted by Hawks05 View Post

Another question I have is what did you use to clean/scrub the CC door before applying the Fireblack125 gasket?

I didn't use fireblack gasket. But I think I used paint thinner to prep. It's been awhile.
post #8 of 13
Thread Starter 

Well I'm doing a test run with my fire basket and with everything closed (NOT THE EXHAUST) my probe a grate level close to the middle of the pit is reading 270 and it appears the temp wants to keep climbing.  Now I did fill the basket with hardwood lump coal which could be the problem.

 

Would I be better off putting a little coal in the basket and using mainly pecan mini logs?

 

At 325PM it has not hit 287

post #9 of 13
Lump burns pretty hot. That's probably why the high temps.
Myself I would use charcoal to get started and then add 2 splits. And let the smoker get settled in. Then add 1 or 2 preheated splits "preheat on lid of firebox" when the temp would start dropping.
You could also fire up with a weed burner torch only using some smaller splits.

Fire management and maintaining the temp you want will take practice.

photo image_34.jpg

Picture above is just getting smoker fired up.
Edited by hardcookin - 8/3/16 at 6:00am
post #10 of 13
Thread Starter 

Well I can do fire management as I have smoked brisket and ribs many times on it.  But I have since added the fire basket in hopes of giving myself a little free time in between tending the fire instead of checking on it every 15 mins. 

 

Plus I have since added gasket around the CC and sealed around the exhaust pipe.

 

 

Did some research and it appears the burn characteristics of pecan is low and slow.  so hopefully this will allow for better control with a little more free time in between checks.  I think after this weekend I may want to add some gasket material (not sure what to use because of the heat produced in the FC) in between the 2 halves of the FC. 

post #11 of 13
I just figure an offset is something you are going to feed splits every 30 mins. They are designed to move a lot of air. In my opinion they offer the best flavor.

I hope you achieve what you are trying to do. Good Luck!!
post #12 of 13
I have the convection plate for my Chargriller trio
It's heavy and does a good job but I still had to block off some of the holes to get an even temp from one side to the other
post #13 of 13

Here is a slightly different design I used on another offset smoker.  I cut strips of metal about 3.5 inches wide (and a few 2 inches wide).  They are supported on angle iron rails I screwed to each side of the cooking chamber.  I move these back and forth to control where the smoke and heat goes depending on my meat. Seems to work pretty well. The holes work too but are not adjustable.  

 

I used strips of lawn edging about 3/32" thick.  It was easy to cut with a hack saw. NOTE: it was  galvanized and I soaked the pieces in some muriatic acid from ACE hardware to dissolve the galvanizing off. Only took 30 seconds or so, but must be done outside for the fumes. 

 

These have worked for several years for me. They don't rust now with a buildup of grease on them. 

New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Charcoal Smokers
SmokingMeatForums.com › Forums › Smoking Supplies & Equipment › Charcoal Smokers › Calling all OKJ Longhorn owners!