or Connect
SmokingMeatForums.com › Forums › Announcements › Roll Call › Hello from California with my Mini WSM
New Posts  All Forums:Forum Nav:

Hello from California with my Mini WSM

post #1 of 19
Thread Starter 

New to the forum and glad to be here.

 

I am in Modesto, CA. and built my Mini WSM in July.  (build video)

 

I am a novice to smoking, but no novice to bbq, grilling or eating! I was going to buy a smoker but found this forum and a few videos on building a mini wsm. I had a very old smokey joe (20+ years) that I only used for camping trips. Spent a Saturday buying parts and BAM... $60 later I have been smoking basically every weekend since. 

 

Here are some pics of the build and my first tritip....I look forward to being a part of the club.

 

post #2 of 19
Welcome! Great job on your Mini-WSM and your first smoke!
post #3 of 19
Hey

Welcome to the Smoking forum. You’ll find great , friendly people here, all more than willing to answer any question you may have. Just ask and you’ll get about 10 different answers—all right. LOL. Don’t forget to post qviews.

Gary
post #4 of 19
Radioyaz,
Welcome to SMF.
post #5 of 19
Thread Starter 
Thanks! Glad to be here.
post #6 of 19
What's supporting your lower grate? I built my mini about the same time as you.
post #7 of 19
Radioyaz
Looks like you went in my garage and took
Black Beauty!! Lol
post #8 of 19
Thread Starter 

Quote:
Originally Posted by Welshrarebit View Post

What's supporting your lower grate? I built my mini about the same time as you.

Hey Welsh. I just doubled up the nuts and bolts used for the top grate. I measured 3 3/4 inches from the nuts supporting the top grate and that left it just above the pan. The pan is sitting on my old grill grate which fit perfectly in the steamer tray ring at the very bottom of the pot. I didn't want to use long bolts to support the pan, I thought those might bend if the pot got too hot.

These two pics kind of show it before I painted it. The bottom nuts you see on the outside of the pot are holding the second grate. The top view is the bottom gate just above the clay water pan that is sitting on the grate where the steamer pan would have been in the original pot.

Glad to here you made one too. Did you post a pic?
Edited by radioyaz - 9/11/14 at 1:09pm
post #9 of 19
Thread Starter 
Quote:
Originally Posted by Lemans View Post

Radioyaz
Looks like you went in my garage and took
Black Beauty!! Lol

Hey Lemans,

Tis a beauty. Nice work!
post #10 of 19

texas.gif  Good morning and welcome to the forum, from a finally cooling down East Texas. Lots of great people and tons of information.   Good job ------- looks nice

 

Gary

post #11 of 19

Glad you joined the group. The search bar at the top of any page is your best friend.
About anything you wanna know about smoking/grilling/curing/brining/cutting or slicing
and the list goes on has probably been posted. Remember to post a QVIEW of your smokes.
We are all smoke junkies here and we have to get our fix. If you have questions
Post it and you will probably get 10 replies with 11 different answers. That is
because their are so many different ways to make great Q...
Happy smoken.
David

post #12 of 19
Thread Starter 

Thanks David,

 

Is there a better place or "the" place to post Qviews? I found a thread in the mini wsm board posted some there. I appreciate the advice.

post #13 of 19

:welcome1: , Radioyaz . Welcome to the crew . stake a claim and become a member of the neighborhood.

 

Send plenty of Q-view ( done) and narration , and as always . . .

post #14 of 19
Welcome radioyaz. I'm right down the road in Turlock, but work in modesto. Glad you joined the group.
post #15 of 19
Thread Starter 
Quote:
Originally Posted by MJ Ryder View Post

Welcome radioyaz. I'm right down the road in Turlock, but work in modesto. Glad you joined the group.


Ha. Small World M J. Glad to be here.

post #16 of 19
Quote:
Originally Posted by radioyaz View Post



Hey Welsh. I just doubled up the nuts and bolts used for the top grate. I measured 3 3/4 inches from the nuts supporting the top grate and that left it just above the pan. The pan is sitting on my old grill grate which fit perfectly in the steamer tray ring at the very bottom of the pot. I didn't want to use long bolts to support the pan, I thought those might bend if the pot got too hot.

These two pics kind of show it before I painted it. The bottom nuts you see on the outside of the pot are holding the second grate. The top view is the bottom gate just above the clay water pan that is sitting on the grate where the steamer pan would have been in the original pot.

Glad to here you made one too. Did you post a pic?

The only known smoker in existence that says HI!

217.JPG

Mac-nut smoked chicken:



Kiawe smoked naked ribs:

post #17 of 19
Thread Starter 
That is some good looking grub. Nice!
post #18 of 19
Thread Starter 

So I wanted to update this post...I have been smoking A LOT...just don't always have the time to post Q-views. But I did finally cut the bottom out of my smoking chamber/tamale pot. I just drilled a whole bunch of holes and some wire cutters

 

 

I know I know...it's pretty ugly...but...WHO CARES...I never see it!  Now I can get the temps up to crisp up some chicken skin. Nice!  However, the direct heat to my clay pot heat diffuser cracked that baby so I simply wrapped it up in HD aluminum and use a thin sheet of aluminum on top of it for drips or if I want to use water (sometimes I do). If I remember to take pics this weekend I will post.

 

Happy Smokin'!  Have a good holiday!

post #19 of 19
Welcome back and good luck.
I followed everyone's advice and cut the bottom out of mine to begin with. I'm so glad I did. I did not use the terra-cotta pot, I found a 10 1/2 inch skillet at Walmart for $10. It's the exact same size as the charcoal basket. It will take the heat very well and will not crack or break. Good luck with yours.
-Ryan
New Posts  All Forums:Forum Nav:
  Return Home
  Back to Forum: Roll Call
SmokingMeatForums.com › Forums › Announcements › Roll Call › Hello from California with my Mini WSM