Airflow regulator on top?

bigeateruk · Jun 3, 2014

Hi All,

New to the forum and am in the process of doing the mods to my ECB. I live in Bristol in England and this is my first smoker so not only a newbie to this site I am a novice when it comes to smoking. Have currently put holed in the charcoal pan and have got a grill to get the coals raised off the bottom. Have a thermometer gauge which i fit this week and am wondering if I need to do the airflow regulator and does it make a lot of differnce. I am quite excited to use it as the first two times was without mods and was quite a struggle so am looking forward to better results.

Have also seen something about the gap around the lid and am wondering whether I really need to fill this. Have seen that someone has used some rope to fill the gap. Again is this gonna mke a massive difference.

Anyway any help with this smoker would be massively appreciated as I am determined to use this and get good results from it as opposed to spending hundreds of pounds on a Weber or the like.

Cheers

ron eb · Jun 4, 2014

I don't know if this is the same ecb but these are the mods I did on mine.

grill and holes in coal pan, top damper, 3 bottom dampers, new thermometer,

fiberglass oven gasket to seal gap in the lid. before these mods I had no control.

These upgrades make all the difference. Go through this thread to see pics.

http://www.smokingmeatforums.com/t/146912/everything-is-coming-together

venture · Jun 4, 2014

If you are talking about the old time ECB? Like this?

Old ECB 001.JPG

venture
Feb 7, 2014

Unless radically modified, they had huge flaws, one of which was the inability to regulate the air intake at the bottom. They were open at the bottom, so intake dampers were not much to think about?

Using the top damper or any exhaust damper to regulate air flow and pit temp is akin trying to stop the wind from blowing or making the wind blow? Additionally, trapping smoke and air flow at the point where it should be exhausting? You are inviting stale smoke and creosote flavor on your meat.

Others may disagree. That is fine.

That is not to say you can't get good smokes from one because you can. It is just tricky. Many of us started with one of those.

There is a lot that can be learned from one of these, and that knowledge can guide you on your next smoker purchase. Or possibly your scratch build of a better designed upright?

Keep at it, you will get there!

Enjoy the journey!

Good luck and good smoking.

bigeateruk · Jun 5, 2014

Ron EB - think the one you have is the Brinkmann Gourmet smoker which has a case at the bottom enclosing it whereas mine is open at the bottom. Have seen someone take off the legs and sit it on the floor and put a damper on the side at the bottom so could always try that. Have seen that people have blocked the gap at the top so may do that and fir the air damper on top. Its all fun doing the mods.

Venture - mine looks like that just a different colour. There is a gap around the lid at the top to let smoke out so no stale smoke, creosote flavour just having a problem with temp. Gonna give it a run with the mods i have done so far and see how it goes then go from there.

Thanks for the advice

ron eb · Jun 5, 2014

Good luck Bigeateruk.

venture · Jun 6, 2014

Yeah?

Strange as it seems?

I often wondered if that gap around the top wasn't part of their design plan. Maybe and maybe not

If nothing else, it was basic and at the right price!

It was an early and entry level design.

Got many of us started.

Good luck and good smoking.

bpinmi · Mar 14, 2015

I cut a hole in the lid and attached a soup can lid using a small bolt. I generally leave it about 1/3 open. Helps with airflow. If I'm running too hot I can close it and temps will drop, if I I need more heat I can open it up more and pull more air through to heat up the coals.

image.jpg

bpinmi
Mar 14, 2015

BigeaterUK said:
Hi All,

New to the forum and am in the process of doing the mods to my ECB. I live in Bristol in England and this is my first smoker so not only a newbie to this site I am a novice when it comes to smoking. Have currently put holed in the charcoal pan and have got a grill to get the coals raised off the bottom. Have a thermometer gauge which i fit this week and am wondering if I need to do the airflow regulator and does it make a lot of differnce. I am quite excited to use it as the first two times was without mods and was quite a struggle so am looking forward to better results.

Have also seen something about the gap around the lid and am wondering whether I really need to fill this. Have seen that someone has used some rope to fill the gap. Again is this gonna mke a massive difference.

Anyway any help with this smoker would be massively appreciated as I am determined to use this and get good results from it as opposed to spending hundreds of pounds on a Weber or the like.

Cheers

thinblueduke · Mar 14, 2015

I drilled holes in the lid and I leave them open all the time. Combined with the rope around the lid, it makes a big difference. Previously, the smoke would exit through the gap around the lid without ever reaching the food. With the rope in place (others use an oven gasket), the smoke is forced up through the top grate, where I know it's doing its job, and goes out the top. If you have the means, I would recommend doing both mods.

ventholes.jpg

thinblueduke
Mar 14, 2015

These holes were a bit too small. I widened them to about 6mm.

getarope.jpg

thinblueduke
Mar 14, 2015

The rope sits right under the ridge on the lid. To keep it in place, I used a pair of pliers to flare the rim out just a little bit after affixing the rope. The seal doesn't need to be perfect. It's OK if a little smoke gets through.

Search

Search

Airflow regulator on top?

bigeateruk

Newbie

ron eb

Meat Mopper

venture

Smoking Guru

Old ECB 001.JPG

bigeateruk

Newbie

ron eb

Meat Mopper

venture

Smoking Guru

bpinmi

Smoke Blower

image.jpg

thinblueduke

Meat Mopper

ventholes.jpg

getarope.jpg

Similar threads

Latest posts

Hot Threads

Spammer PMs, Anybody Else?

Questions for RecTeq owners

Lost my dad yesterday

On the Edge of Trying Sausage Making

Took a stroll this afternoon