brinkmann pitmaster mods

waygu tim

Fire Starter

Original poster

Jul 17, 2012

50

56

goshen indiana

• Apr 3, 2014

• #1

hi all today i started work on my brinkmann pitmaster we did all of the design work and ordered the metal for it using expected metal for the charcoal basket and 1/4 inch metal for the baffle and turning plates

IMG_0113.JPG

• waygu tim
• Apr 3, 2014

IMG_0111.JPG

• waygu tim
• Apr 3, 2014

IMG_0108.JPG

• waygu tim
• Apr 3, 2014

IMG_0109.JPG

• waygu tim
• Apr 3, 2014

IMG_0110.JPG

• waygu tim
• Apr 3, 2014

 

Last edited: Apr 4, 2014

kc5tpy

Master of the Pit

May 12, 2013

4,352

188

Newark on Trent, United Kingdom.

• Apr 4, 2014

• #2

Hello Tim.  Lookin good so far.  Good luck.  Keep Smokin!

Danny

 

waygu tim

Fire Starter

Original poster

Thread starter

Jul 17, 2012

50

56

goshen indiana

• Apr 16, 2014

• #3

hi guys well i got my metal parts today we are about done on the smoker build the baffle plate is made out of 3/16 metal and the tuning plates are made of 1/4 metal need to finish the front shelf and brace the legs and extend the chimney down to grate level and replace the wheels and repaint it then put the seal on then i am done i am so happy right now  i did fire it up today i could the the difference right away it was amazing

IMG_0120.JPG

• waygu tim
• Apr 16, 2014

IMG_0121.JPG

• waygu tim
• Apr 16, 2014

IMG_0122.JPG

• waygu tim
• Apr 16, 2014

IMG_0123.JPG

• waygu tim
• Apr 16, 2014

IMG_0124.JPG

• waygu tim
• Apr 16, 2014

IMG_0125.JPG

• waygu tim
• Apr 16, 2014

IMG_0126.JPG

• waygu tim
• Apr 16, 2014

IMG_0127.JPG

• waygu tim
• Apr 16, 2014

IMG_0128.JPG

• waygu tim
• Apr 16, 2014

IMG_0129.JPG

• waygu tim
• Apr 16, 2014

IMG_0114.JPG

• waygu tim
• Apr 16, 2014

IMG_0115.JPG

• waygu tim
• Apr 16, 2014

IMG_0116.JPG

• waygu tim
• Apr 16, 2014

IMG_0118.JPG

• waygu tim
• Apr 16, 2014

IMG_0119.JPG

• waygu tim
• Apr 16, 2014

 

Last edited: Apr 16, 2014

waygu tim

Fire Starter

Original poster

Thread starter

Jul 17, 2012

50

56

goshen indiana

• May 2, 2014

• #4

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0143.JPG

• waygu tim
• May 2, 2014

IMG_0144.JPG

• waygu tim
• May 2, 2014

IMG_0146.JPG

• waygu tim
• May 2, 2014

IMG_0147.JPG

• waygu tim
• May 2, 2014

IMG_0149.JPG

• waygu tim
• May 2, 2014

IMG_0150.JPG

• waygu tim
• May 2, 2014

IMG_0151.JPG

• waygu tim
• May 2, 2014

IMG_0152.JPG

• waygu tim
• May 2, 2014

 

aaardvark

Newbie

Jul 7, 2014

2

10

• Jul 7, 2014

• #5

Tim:

Looks great.  I am about to start a restoration of a BPD and want to make the same mods.  Do you happen to recall the measurements for the heat shield.  Top I can figure out, but 1) bottom and 2) some way to guesstimate the curve would be very helpful.

 

waygu tim

Fire Starter

Original poster

Thread starter

Jul 17, 2012

50

56

goshen indiana

• Jul 7, 2014

• #6

hi there i will try and help u the best way i can a email address or phone number that would be grate and make sure to use only dry wood is what i found works the best

 

aaardvark

Newbie

Jul 7, 2014

2

10

• Jul 7, 2014

• #7

Tim:

Thanks for the speedy reply.

You can reach me at [email protected]

Rob