help, salmon fillet stuck at 127

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

bagbeard

Meat Mopper
Original poster
May 24, 2013
228
17
Scotland, Ontario, Canada
i followed the recipe in Jeff's new book to a tee except i left the fish in the fridge till the smoker was ready.  he says 4-5 hrs and im at almost 7 hrs. the salmon wasnt especially thick and my smoker chamber temp has been riding a steady temp of 152-160. not sure what to do.  temp of fish hasnt changed in over and hour and a half
 
Giving this a bump.....haven't smoked fish...hoping someone with see ya and help.

Are you sure your thermometer to accurate?

Kat
 
Last edited:
probes have been good for the last few cooks.  not sure what to do . going to pull it off and check with a fork.  hate to mess up the nice fillet if its not done.  getting late though
 
well im eating it now.  omg. never made anything close to fish this good.  only problem is i have 1/2 a fish here and no one to enjoy it with.  wife went to bed hour a go.  woke her up and fed her a chunk and didnt get yelled at .must be good.  just kidding, lol. pics to come
 
Inadequate pellicle led to evaporative cooling from the surface which kept fish cold.

The temp of the fish clearly got above 140 eventually based on the white ooze.
 
Looks good. I prefer to smoke my salmon with the skin off. That way I can remove the mud vane and the fat. Produces a much better product IMO. I run the smoker at about 150 to 160 and remove fish when it reaches 140 to 150 degrees.

 
 
after brining i let it dry in fridge for 3 hours.  do i need longer? the outside of fish was dry.  end result was great. even better today after cooling in fridge. mixed with cream cheese on a bagel
 
 
i think my temp probe is kinda cheap and doesnt give good readings when it is into the meat only a little bit, because the fish was flaky and done. 
 
Looks good. I prefer to smoke my salmon with the skin off. That way I can remove the mud vane and the fat. Produces a much better product IMO. I run the smoker at about 150 to 160 and remove fish when it reaches 140 to 150 degrees.


 

The "mud vane" is nothing more than slow twitch muscle tissue fish use for almost all general movements. The rest of the meat is fast twitch muscle tissue the fish uses for rapid or high power movement. It literally is little used during most of a fish's movements. With our AK fish it is perfectly good and free of off flavors... it ain't a catfish! :biggrin:
 
after brining i let it dry in fridge for 3 hours.  do i need longer? the outside of fish was dry.  end result was great. even better today after cooling in fridge. mixed with cream cheese on a bagel

 

Different ambient conditions change how fast and well the pellicle forms. I have never seen a refrigerator with enough air circulating to produce a pellicle. I use a fan on racks set on the counter. Lots of air and good drying conditions can mean a pellicle is done in an hour. Sometimes it takes several. I cannot emphasize enough how critical the pellicle is...
 
Different ambient conditions change how fast and well the pellicle forms. I have never seen a refrigerator with enough air circulating to produce a pellicle. I use a fan on racks set on the counter. Lots of air and good drying conditions can mean a pellicle is done in an hour. Sometimes it takes several. I cannot emphasize enough how critical the pellicle is...
Funny I just PMed you with some questions about this.
yeahthat.gif
 
Different ambient conditions change how fast and well the pellicle forms. I have never seen a refrigerator with enough air circulating to produce a pellicle. I use a fan on racks set on the counter. Lots of air and good drying conditions can mean a pellicle is done in an hour. Sometimes it takes several. I cannot emphasize enough how critical the pellicle is...
so you figure my pellicle wasnt adequate, would that inhibit temperature rise of fish?  if so how does that work.  if chamber is 155 then shouldnt meat reach that temp eventually? 7 hrs is a long time.  or maybe it was probe is no good at shallow depths. no worries about fish at rm temp for 2 hours?
 
Yes, the pellicle is critical to maintaining control when smoking fish and the lack of an adequate pellicle allows the moisture to evaporate from the fish and cooling it.

Evaporative or adiabatic cooling works because evaporating water takes a tremendous amount of energy with it when it goes. That energy is called "latent heat of vaporization" and is 970BTUs per pound of water. It takes quite a lot of heat to overcome that... So the fish continues to cool from the surface while heat in the smoker attempts to keep up with it.

The pellicle seals the surface and reduces that evaporative cooling dramatically.

Fish takes a lot longer than a few hours to go bad at room temp... but cooler is certainly better and the treatment the fish got prior is also important to how room temperature will affect it. It also is being cooled adiabatically but due to the lower temperature of the product it dries faster than the water inside the fish can be mobilized.

With only 15 degrees difference between fish and ambient temperature and active cooling going on there is little temperature differential to add heat to the fish.

And of course that brings up the bigger question of what the temperature actually was in your smoker. Say your smoker thermo reads 5* high and the probe reads 5* low... Hard to get much temperature gain there. How sure are you that the smoker temp is correct? I have seen smoker temps that read more than 25* off actual...
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky