My brand new Traeger Texas Smoker!

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

duanes

Smoke Blower
Original poster
SMF Premier Member
Mar 27, 2011
126
13
Raleigh, NC
I haven't been on this forum for awhile, a little busy with moving from New Jersey to North Carolina.  Gettin settled in and finding less time available to babysit my vertical smoker, I spent a few dollars - Traeger Texas Smoker.  Besides, I'm in BBQ country now so I need to step up my game!
36.gif


Not sure this is the right spot for posting (I think it loosely qualifies as a wood smoker
icon_question.gif
) Tomorrow it will be christened with an 8lb. Boston butt.  But that is getting ahead of the story.  My son was very helpful in taking pictures (thank you buddy!) from box to seasoning and I thought I would share the experience, especially for anyone considering buying a Traeger.

 I bought it at Hudson's Hardware in Clayton - fine friendly staff.  To start, you definitely need 2 to unload:

b0465bd6_Traeger_TS_01.jpg


31378c24_Traeger_TS_02.jpg


3d5311fa_Traeger_TS_03.jpg


Everything was packed very well with no parts damaged from shipping.

008a0fb0_Traeger_TS_04.jpg


There weren't very many parts to assemble and the instructions were very clear.  A thick recipe book came with it - time will tell if there are any golden recipes in it.  The quality of the parts are good, nothing felt cheap.  The steel used for the smokers isn't 1/4" but it doesn't feel flimsy.  All the parts including, legs, handle, hinges, doors, etc.,. all had a nice fit and finish.  The tires have nice rubber - not too hard or soft.

e30bf754_Traeger_TS_05.jpg


Here is the smoker with grill, grease pan and baffle removed.

3520bb4d_Traeger_TS_06.jpg


Here is heavy guage stainless steel heat baffle in place.

bd88b82e_Traeger_TS_07.jpg


Here is heavy guage stainless steel grease pan in place.  Pan fits on lips, tilting to one side to drain into trough (you can see trough in pic above to the right).  the trough has drain hole that bucket hooks to on the outside.

9e05cb3b_Traeger_TS_08.jpg


Here is the smoker with porcelain coated grill in place.  Rack space is about the same as the three racks combined on my vertical smoker.  I should be able to get 6 rib racks laying flat no problem.

Assembly was a snap, less than 30 minutes from unloading to finish with a total of 10 bolt sets.  Allen wrench and two wrenches were included.

f86fd8ac_Traeger_TS_09.jpg


Here is the pellet hopper ready to go for intial startup.

f7d8eea0_Traeger_TS_10.jpg


First time use requires running the unit for about 7 minutes until pellets start dropping into the firepot and about another 15 minutes until the pot fills up and ignites.  Waitin for the pellets to come out was like a kid waitin for gumballs to drop after puttin my nickel in!

15a91388_Traeger_TS_11.jpg


Here pellets are starting to smoke.

e5d2397f_Traeger_TS_12.jpg


... a lot more smoke!

f6f9043f_Traeger_TS_13.jpg


...and finally a full flame per instructions.  At this point, instructions say to shut off and let cool down.

73f6d92d_Traeger_TS_14.jpg


Hard to see hear but TBS coming out of the stack after running for awhile for the seasoning.  The inside and out smoked a bit once it hit 400+ degrees burning off the manufacturing oils.

b7470c51_Traeger_TS_15.jpg


Seasoning is to run on high for 45 minutes (I gave it an hour and a half)  Here is the controls with digital readout that indicated about a 15 degree swing once it hit operating temperature - the primary reason for buying this unit.  It was about 9o degrees today and peaked out around 440.  The dial has detents so you pick one of 8 presets.  The panel is a little hard to read unless you bend  down a bit.  I respect the art of smoking but "set and forget it" leaves more time for beer and friends!

10d6737b_Traeger_TS_16.jpg


And here is the smoker after the seasoning.

ba055a51_Traeger_TS_17.jpg


So far it looks like a great smoker.  Nit-picking, the legs are sturdy but cross bracing would inspire more confidence.  I could see getting hung up and pulling to hard and bending a leg.  The spread on the legs is a little narrower than I would like.  It would be nice to have a bracket to wind the cord up when not in use (just hangs from bottom).

The lid has a button hole with cap on right of lid for an optional thermometer.  I need to figure out where I am going to run my probe wires for my Maverick wireless.  I'll need to add a bracket somewhere to hold the Maverick sending unit.

I can't wait to fire 'er up tomorrow!  I'll post the boston butt from beginning to end and continue the story...
 
looks pretty cool. i've never seen anything like that in person, let us know how it comes out!
 
Great looking smoker!  You definitely have a wood smoker and don't let anyone tell you any different, beside they are just jealous if they do
smile.gif


Make sure you tin foil the the drip tray before cooking on it, that will make clean up a lot easier.
 
Last edited:
I'm sure there are "deal" hound dogs out there that can find a great deal, but most places I looked, it was $1,000 plus shipping and/or tax - which is about what I paid.  There was one online site that was a little less but my confidence wasn't there in the event I had shipping problems.
 
I put some bricks in the bottom of mine to help with heat retention in the winter.  I also put a few extra on the right hand side to help even it out a bit...my left side runs hotter than the right side but my smoke stack is in the middle.  I assume the heat difference is due to the slant of the drip tray.

Glad to see you are rolling along with it.
 
Those are all the details I'm anxious to deal with.  How many bricks did you use?  If you get a chance, could you post a pic with the bricks?  How cold has it been when you have smoked and how did it perform?  do you leave the bricks in year 'round.  Do you know how much variance in temp from left to right?  Are there any hotspots?  Thanks for the info!
 
Not the best pic but you can see what I did.  I never take them out except when I vac it out.

95ccf82c_smugshot6622823-X3.jpg
 
 Wow , great lookin smoker 1K huh?  looks worth it you'll have a lotta great smokes. Afraid I'll have to be stickin with me little Electric Brinkmann  $124.00 at Wally-World .

I can live vicariously threw you guys with the high tech & coustom set up ....I do want one some day .....I be keepin me eyes open ...BUT ...keep smokin .....
 
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky