Vertical Propane Smoker Rebuild
- Thread starter haus of smoke
- Start date
-
Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.
michael ark
Master of the Pit
I am using only a 10 psi regulator. This burner is designed to use a 20psi regulator - but that would be totally nuts for my application. I get more control at the lower end by using this smaller regulator.
texasburner
Newbie
No. A friend of mine fabricated the racks and I added the guides. The cabinet itself was built in 1957 as basically a rack mounted server cabinet...before there was such a thing. It housed some serious vacuum tube powered stuff (a Pulse Height Analyzer) that required very direct cooling - it was designed to force air through a filter in the base - up the right plenum across each rack out the exit plenum. Works pretty good for smoking meat.
The overlapping grease flashing/heat baffle worked wonderfully - no grease in the bottom, no flare ups, The temporary water tray has too much surface area and had to be covered to run up the heat for final roasting. The change-of-state from a liquid to a vapor and directly to steam in an environment where there is no build up of pressure means that the steam itself can't rise above 212°F. Ideally, I usually smoke at 225° to 235°F. The volume of steam needs to be low enough so that it is mixing with hotter air to achieve a mix that is higher then 212°F. The final water tray will have a smaller surface area and be a couple of inches more above the burner.
Sweet!!!! Awesome build and great Ideas!!!! Those turkeys look awesome!!!
Love the burner! Great job! Now all you need is a gas control valve with a temp sensor and you would be all set!
SOB
Love the burner! Great job! Now all you need is a gas control valve with a temp sensor and you would be all set!
SOB
Number 10 cans covered tightly with foil with small holes sitting on the corners of the pipe burner and, depending on what I am smoking, filled with hickory/apple chips or hickory sawdust. Final configuration will have a removable firebox for cooking only with charcoal/wood when desired.
I've changed my mind on the 10 psi regulator size. Spent the last few weeks smoking in very cold air temps and having a 20 psi regulator would certainly bring the smoker up to temp quicker.
Propane smoker update.
The burner I had made works good, but it is difficult to light if it goes out. The flame does not go all the way around. I have to light each section of pipe if the flames are low.
The people at Tejas Smokers told me they sold a mess of these pipe burners because of this thread on this forum. Tejas has improved on the concept and now sell an excellent cast iron burner where the flame goes all the way around and it also has a place for a Pilot light that will re-light the burner if it goes out. You must supply your own gas pipe connection between the venturi and the burner so you can center the burner in your smoker.
http://www.tejassmokers.com/castironburners.htm
Scroll down to part numbers "GRILL1" and "PILOT"
Tip of the day: Double up a piece of parchment paper about the size of your piece of meat and set your pork shoulders on them in the smoker. I can drag each butt around, turn them and remove them without losing shreds of meat though the grid. Easier cleanup and the patchment paper seems to keep the meat a little juicier. Works for whole chicken as well.
(NOT Wax Paper, not Butcher Paper, not Freezer Paper the box will say "Parchment Paper")
The burner I had made works good, but it is difficult to light if it goes out. The flame does not go all the way around. I have to light each section of pipe if the flames are low.
The people at Tejas Smokers told me they sold a mess of these pipe burners because of this thread on this forum. Tejas has improved on the concept and now sell an excellent cast iron burner where the flame goes all the way around and it also has a place for a Pilot light that will re-light the burner if it goes out. You must supply your own gas pipe connection between the venturi and the burner so you can center the burner in your smoker.
http://www.tejassmokers.com/castironburners.htm
Scroll down to part numbers "GRILL1" and "PILOT"
Tip of the day: Double up a piece of parchment paper about the size of your piece of meat and set your pork shoulders on them in the smoker. I can drag each butt around, turn them and remove them without losing shreds of meat though the grid. Easier cleanup and the patchment paper seems to keep the meat a little juicier. Works for whole chicken as well.
(NOT Wax Paper, not Butcher Paper, not Freezer Paper the box will say "Parchment Paper")
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.
Similar threads
Hot Threads
-
Our Second piece of Heaven, Little piece on the Atlantic Ocean
- Started by DRKsmoking
- Replies: 57
- General Discussion
-
How Do I Get Rid of These Armadillos?!!
- Started by seenred
- Replies: 41
- Blowing Smoke Around the Smoker.
-
Non fat dried milk
- Started by hog warden
- Replies: 37
- Sausage
-
Featured A couple thick strips please!
-
Getting to the bottom of what happens to cure in smoked sausage
- Started by hog warden
- Replies: 31
- Food Safety
