Adding Propane to a simple Brinkmann 2-Door Vertical Charcoal Smoker

  • Some of the links on this forum allow SMF, at no cost to you, to earn a small commission when you click through and make a purchase. Let me know if you have any questions about this.
SMF is reader-supported. When you buy through links on our site, we may earn an affiliate commission.

grillinggator

Newbie
Original poster
Mar 20, 2011
4
10
[h2]Adding Propane to a simple Brinkmann 2-Door Vertical Charcoal Smoker[/h2][h2]
Problem:[/h2]
I am relatively new to smoking and I have had some problems keeping a consistent temperature during all day smoking.  I have been a traditional griller for years but have the bug to start smoking.  I started with a trial by ‘fire’ and had okay results but have been reading a bunch on different mods and improvements.  This site has been full of great tips.
[h2]Solution:[/h2]
I wanted to make a simple low cost mod to add a burner to the base of my Brinkmann.   This would allow me to dial in my temperature as I start to master the charcoal and wood combinations.  As I searched around the web there seemed to be a lot of complicated ways to add propane.  My solution was simple, cheap and used off the shelf parts.
[h2]Items: [/h2]
  1. Single Burner Propane Stove (by Northwest Territory).  I found it at Kmart in the camping section for $9.99.
    1e39f4a9_Parts_Burner.jpg
  2. Coleman 5ft Propane Hose and Adapter so I could use a regular propane tank (Kmart, $28)
    b8312256_Parts_Hose.jpg
  3. Threaded Rod (1/4 in x 1 ft). Home Depot, $0.98
    3d0172fe_Parts_ThreadedRod.jpg
  4. Tension Pin (3/8 in x 2 in). Home Depot, $0.75
    50394257_Parts_Expansion.jpg
  5. Hex Nuts (1/4 in). Home Depot, $0.98
    1ccb141a_Parts_Nuts.jpg
  6. Hammer, Metal drill bits.
[h2]Steps:[/h2]
Turn your Brinkmann upside down and drill a hole in the center to match the valve diameter.

94c68b91_Mod_Hole_Bottom.jpg


Disassemble the burner and pull off the temperature knob.

b66f9dd6_Parts_Burner_AsIs.jpg


Insert the valve assemble through the hole and connect the remaining top part on the inside of the base. 

c46c7c12_Valve1.jpg


Inside view

3cd240e5_Burner_Installed.jpg


Drill a 1/4in hole in the leg so that the 1ft threaded rod can fit through it.

9b734da3_Mod_Hole_Leg.jpg


Put two hex nuts onto the threaded rod so the extend past the end a little bit.  This will be used to protect the threads while we hammer.

f40bf376_ValveExtension1.jpg


Hammer the end of the rod into the Tension Pin.  It should go in about 3/4in.  Once in, tighten a hex nut against it and remove the other two hex nuts.

c6cb5c54_ValveExtension2.jpg


Insert the rod with the attached Tension Pin through the leg hole and push it on the valve stem.

e969bea0_ValveExtension3.jpg


Point the valve stem toward the front left leg of the grill.  Insert the rod and connect the valve stem.

d97ae0ea_ValveExtension4.jpg


5013ee5b_ValveExtention6.jpg

 

Drill out the plastic temperature knob that came with the burner to remove the flat part.  Don’t make this hole too big as you want it to screw tightly onto the threaded rod.  I added a hex nut first so I could tighten down the knob once it threaded onto the rod.

86e0b90e_Knob1.jpg


b6f0f96d_Knob2.jpg

 

Connect the propane hose extension and connect it to the tank.
62fd2427_PropaneConnection.jpg

[h2] [/h2][h2]Base:[/h2]
I used some scrap wood to make a simple base for my smoker.  It sits over one of my deck benches and lets me work at a comfortable height.  Here is a picture of the base.  Notcie the temperature knob sticking through the leg.

8ea30b6a_SmokerOnPlatform.jpg

[h2]Finished:[/h2]
Burner in the bottom with the threaded rod/knob on the leg.

d97687b3_Brinkman_After3.jpg


High flame

9fc1d45b_Burner_HighFlame4.jpg


Low flame

301a49e7_Burner_LowFlam.jpg


Time to smoke...
 
Looks good. Cant wait to see how it does.
 
Thanks Mudd.  It worked like a champ to help balance out my temps as needed.  I am headed for the wok basket next.  Once I learn more I think I will be able to remove it down the road but my goal while learning is to also eat what I'm smoking :)
 
I guess I was just lazy with my vertical. Stuck the hookup line thru the lower vent and ran it to a single burner cast iron stove. Cable of over 400º on a warm day.

d82d9b99_SetUp0002.jpg
 
Last edited:
SmokingMeatForums.com is reader supported and as an Amazon Associate, we may earn commissions from qualifying purchases.

Latest posts

Hot Threads

Clicky